afx light IBAR1815 Manuel D'utilisation page 3

Orientation
This f ixture m ay b e m ounted i n a ny p osition, p rovided t here i s a dequate r oom f or v entilation
When s electing i nstallation l ocation, t ake i nto c onsideration l amp r eplacement a ccess a nd r outine m aintenance.
Safety c ables m ust a lways b e u sed.
Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or restricted
ventilation.
If t he e xternal f lexible c able o r c ord o f t his l ight i s d amaged, i t s hall b e e xclusively r eplaced b y t he m anufacturer o r h is s ervice
agent o r a s imilar q ualified p erson i n o rder t o a void a h azard.
Make sure the installation position is stable before you fix the light. When the light is reverse hanging, make sure the light
will not fall from the truss, use the safety cable go through the truss and bracket of the light as a supporting, to avoid the
light to fall down. There is no entrance to the work area during mounting. Periodically check if the safety cable has fretted
away o r c lamp i s l oosened. W e w ill n ot t ake a ny r esponsibility f or d amages c aused b y a b adly i nstalled u nit.
Power S upply a nd S ignal C able C onnection
1. M ains P ower c onnection
The exclusive plug should be used between the connection of unit and power. Please ensure that the rated voltage and
frequency a re a ccordance w ith t he p ower s upply. T he r equired i nput v oltage a nd f requency a re: 1 00-­‐240VAC
We s uggest t hat e very l ight h as a n i ndependent s witch s o t hat y ou c an t urn o n o r t urn o ff t he l ight r andomly.
Note: t he g round w ire ( yellow/green d ouble-­‐color w ire) m ust b e s afely c onnected, t he e lectrical i nstallation m ust b e i n
accordance w ith t he r elated s tandards
CAUTION: W hen i nstalling t he d evice, m ake s ure t here i s n o h ighly i nflammable m aterial w ithin a d istance o f m in.5m!
2. C onnection o f S ignal C able
You can use the 3-­‐pin XLR cable to connect the output socket of the master and the input socket of the slave light. Connect
the DIGITAL OUT socket of the master and the IN socket of the slave light, then, connect the OUT socket to the IN socket of
the n ext l ight. O rdinal t o c onnect a ll t he l ights a s b elow:
1 2 3
I N I N I N
O U T O U T O U T
The c onnection b etween t he o utput o f m aster a nd i nput o f p roduct, i t's a vailable t o u se t he 3 p ins X LR c able w hich p rovided
by t he m anufacturer. S ignal c able f rom t he D MX o utput o f t he c ontroller t o t he i nput o f t he f irst m aster l ight, a nd c onnect t o
the DMX input of second slave light from the DMX output of the first master light, analogously, till connected all the slave
lights, and insert the last connector to the output of the final light. (Notice: the diameter of core of every cable should be
0.5mm at least, double core shelter cable should be used).The signal connecting must use the attached 3 pins XLR cable.
Notice, a ll t he i nternal l ead w ire o f t he 3 p ins X LR c able s hould n ot t ouch t o e ach o ther o r c onnect t o t he c onnector.
A DMX signal terminator is recommended on the last unit of the chain. DMX terminator is a XLR connector with a 120Ω
resistor b etween t he p in 2 a nd p in 3 o f t he X LR c onnector
© Copyright LOTRONIC 2015 IBAR-1815 Page 3