Table des Matières
Publicité
10.1 Guide pour le parcours de la cheminée
Élevez les sections de cheminée horizontales de 1/4 po/pi (21 mm/m)
35 pi
DIMENSIONS ARE IN INCHES
NAME
DATE
FRACTIONAL
TOLERANCES:
1/32"
DRAWN
8/25/2017
TWO PLACE DECIMAL
.015"
CHECKED
THREE PLACE DECIMAL
ALL BENDS ARE ASSUMED
.005"
MATERIAL
SIZE DWG. NO.
46DVA-VCH
REV.
TO BE 90 UNLESS NOTED
OTHERWISE.
FINISH
A
34 pi
SCALE
1:5
WEIGHT:
SHEET 1 OF 1
33 pi
32 pi
31 pi
30 pi
29 pi
28 pi
27 pi
26 pi
25 pi
24 pi
23 pi
22 pi
21 pi
20 pi
19 pi
18 pi
17 pi
16 pi
15 pi
14 pi
13 pi
12 pi
11 pi
10 pi
9 pi
8 pi
7 pi
6 pi
5 pi
4 pi
3 pi
2 pi
1 pi
0 pi
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
OTHERWISE.
Figure 10.1.01:
DIMENSIONS ARE IN INCHES
TWO PLACE DECIMAL
20
THREE PLACE DECIMAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
NAME
DATE
DIMENSIONS ARE IN INCHES
DIMENSIONS ARE IN INCHES
TOLERANCES:
TOLERANCES:
DRAWN
8/24/2017
DRAWN
FRACTIONAL
1/32"
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
TWO PLACE DECIMAL
.015"
CHECKED
CHECKED
THREE PLACE DECIMAL
.005"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
MATERIAL
REV.
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
A
DVA 48in Pipe
TO BE 90 UNLESS NOTED
TO BE 90 UNLESS NOTED
OTHERWISE.
FINISH
OTHERWISE.
FINISH
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
NAME
DATE
8/24/2017
DRAWN
CHECKED
MATERIAL
SIZE DWG. NO.
DVA 48in Pipe
REV.
A
FINISH
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
NAME
DATE
TOLERANCES:
DRAWN
8/24/2017
FRACTIONAL
1/32"
.015"
CHECKED
.005"
MATERIAL
REV.
SIZE DWG. NO.
41-DVT Framing
A
FINISH
OTHERWISE.
SCALE
1:50
WEIGHT:
SHEET 10 OF 10
Installation
NAME
DATE
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
8/24/2017
DRAWN
8/24/2017
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
CHECKED
THREE PLACE DECIMAL
.005"
REV.
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
A
DVA 48in Pipe
A
SIZE DWG. NO.
DVA 48in Pipe
TO BE 90 UNLESS NOTED
OTHERWISE.
FINISH
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
INTERDIT
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN
8/24/2017
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
CHECKED
THREE PLACE DECIMAL
.005"
REV.
ALL BENDS ARE ASSUMED
MATERIAL
REV.
A
SIZE DWG. NO.
DVA 48in Pipe
TO BE 90 UNLESS NOTED
OTHERWISE.
FINISH
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
8/24/2017
DRAWN
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
CHECKED
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
MATERIAL
•
La hauteur de la cheminée
SIZE DWG. NO.
A
41-DVT Framing
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
SCALE
1:50
WEIGHT:
est mesurée à partir du collet
d'évacuation situé à l'arrière du
foyer.
•
Longueur totale maximale de la
cheminée = 50 pi
•
Longueur maximale verticale =
35 pi
•
Longueur maximale horizontale =
20 pi avec une élévation minimale
de 10 pi.
•
Coudes horizontaux maximum
autorisés = 3
•
Si plus d'un coude de 90⁰ est
utilisé horizontalement, la section
horizontale maximale est réduite
de 1 pi.
•
Deux coudes de 45⁰ = un coude
de 90⁰.
•
Toujours maintenir une distance
minimale de 12 po entre chaque
coude de 90⁰ dans la conduite
d'évacuation.
•
Voir Section 10.5 pour l'utilisation
d'une terminaison périscopique.
Vérifiez la flamme et assurez-vous
que le restricteur est correctement
positionné.
REV.
SHEET 10 OF 10
Publicité
Table des Matières
