R&G LP0150BK Mode D'emploi page 5


USING THE SCOTCH BLOCK CONNECTORS SUPPLIED RE-ATTACH THE REAR
LIGHT WIRING (WE SUGGEST CUTTING CONNECTOR FROM THE ORIGINAL
REAR LIGHT UNIT AND SPLICING TO THE NEW R&G REAR LIGHT UNIT (IT
CAN ALSO BE SOLDERED) AS DETAILED BELOW).
Page | 5

Fit the new rear light (item 6) to the new licence plate bracket (item 1) as shown in
pictures 8 and 9.

Use the original bolts and secure the new licence plate bracket as shown in picture 10.

If using mini's (R&G mini indicator product code RG370 for bulb type and RG371 for
LED type).

Refit the rear cowling as original.

Place two of the rubber washers onto the indicator stem.

Use the top-hat shaped spacer as arrowed in picture 12 on the indicator and fit into the
rearmost mounting hole as shown in picture 12 and tighten if the indicator is facing in the
wrong direction remove one of the rubber washers and retry, if still incorrect remove both
the rubber washers.

Reconnect the wiring plug socket and check the operation of all lights.

Refit the seat as original.

Fit the new cable cover/under-tray using the two bolts with washers as shown in pictures
13 and 14.

Fit licence plate to new licence plate bracket (it may require drilling or renewing).

IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT
FAR DOWN ON THE LICENCE PLATE HANGER, THERE IS A SMALL
CHANCE OF THE LICENCE PLATE HITTING THE BACK WHEEL UNDER
HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD. IT IS YOUR
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE
AVOIDING ACTION. FAILURE TO CHECK THIS COULD RESULT IN
SERIOUS INJURY.

Depending on local laws, attach enclosed red reflector (item 10) in an appropriate
location.

Please test the indicators, rear light and licence plate illuminator before riding.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OEM WIRES------------R&G NEW REAR LIGHT AND INDICATOR WIRES
GREEN-------------------BLACK=EARTH/RETURN
BLACK------------------YELLOW=SIDE AND LICENCE PLATE ILLUMINATOR
GREEN/YELLOW------RED=BRAKE LIGHT
BLUE CONNECTOR-----RHS INDICATOR
ORANGE CONNECTOR-----RHS INDICATOR
ISSUE 1 08/08/2013 (NSY)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com Email:
5
info@rg-racing.com