De-Activation Of The Delay Function; Sound Volume; Adjusting The Screen - Arregui PLUS C Instructions

<EN>
• Press the button located inside the box once. The box
will emit a long beep and the screen will display the "NEW
CODE" message.
• Introduce the new code from 3 to 8 digits and confirm
by pressing the enter key. The screen will display the
"AGAIN" message.
• Introduce the new code and confirm with the
The box will emit a long acceptance beep, and the screen
will display the "U-CODE R" message, to indicate that it has
been registered.
To change the super-user code, proceed in the following
manner:
• Open the box and don't close it until the procedure is
complete.
• Hit the key.
• Hit the 8 key.
• Press the button located inside the box once. The box will
emit a long beep and the screen will display the "S-CODE"
message.
• Introduce the current super-user code and confirm via
the enter key. If the code is entered correctly the box
will give off a long confirmation beep and will display the
"NEW CODE" message. If incorrectly entered the screen will
display the "ERROR" message, and the process will have to
be started again.
• Introduce a new super-user code of 3 to 8 digits and
confirm with the enter key. The screen will display the
"AGAIN" message.
• Introduce the super-user code again, and confirm with the
enter key. The box will emit a long acceptance beep and
the screen will display the "S-CODE R" message, to indicate
that it has registered.
4. OPERATING THE OPENING DELAY
FUNCTION
This safe contains a delay function, which adds on time from
the introduction of the opening code until the actual opening
comes into effect (from 01 to 99 minutes).
4.1. ACTIVATING THE DELAY FUNCTION
• Introduce the user or super-user code and confirm by
touching the enter key.
• Press the key for five seconds. The screen will display
"--------".
• Introduce the code 789 using the keyboard and confirm by
touching the enter key.
• The box will emit two short validation beeps and will
display the word "DELAY" on screen. The screen will
display "--------".
• Introduce the time delay of between 01 and 99 minutes.
• Important: Always type 2 digits. Whenever the selected
time is under 10 minutes, type "0" as the first digit.

4.2. DE-ACTIVATION OF THE DELAY FUNCTION

enter key.
• Introduce the user or super-user code and confirm by
pressing the
• Press the
"--------".
• Introduce the code 789 via the keypad and confirm by
touching the
approval beeps, and the box will display the word "DELAY"
on screen. The screen will display "--------".
• Introduce the timer delay set at 00 minutes to indicate that
no delay is required.
5. ADJUSTMENTS TO THE SCREEN AND

SOUND VOLUME

5.1 Adjusting the screen

If it is not desirable for access codes to be seen on screen,
then proceed in the following manner:
• Hit the
• Introduce code 33
• Hit the
Every time a digit is introduced on screen, it will be represented
by . To de-activate this option, repeat the same procedure.
5.2 Adjustments to the sound volume
This function allows sound volume settings to be configured
in the strong boxes at 4 different levels of intensity. For this
you have to:
• Hit the
• Introduce code 66
• Hit the
• Introduce the sound volume intensity required, on a scale of
0 to 3. Hit the
» 0 – there is no sound. The screen will display "SOUNDOFF"
» Sound level 1. The screen will display "SOUND 1"
» Average sound level 2. The screen will display "SOUND 2"
» Maximum sound level 3. The screen will display "SOUND 3"
enter key. Wait until delay time expires.
key for 5 seconds. The screen will display
enter key. The box will emit two short
key
enter key
key
enter key
enter key.