Ritter icaro 7 Mode D'emploi page 17

English
• Once slicing has been com­
pleted, wait until the rotary blade
has come to a complete stop.
• After each use, turn the slice
thickness adjusting knob (3) to
the "0" position, in order to cover
up the sharp rotating blade and to
avoid any injuries.
CLEANING
Caution:
Switch the appliance off before
cleaning it; pull the power plug
out off the socket and turn the
slice thickness adjustment
knob (3) to the "0" position.
Clean the food slicer regularly
to prevent the accumulation of
food residue. The rotary blade
must also be cleaned regularly
as described below to prevent its
surface from rusting.
Info:
Over time, an accumulation of
food residue may cause damage
to the surface of the rotary blade,
causing it to rust.
Preparation
• Remove the left­over
holder (12).
I
Remove the finger
p rotection (11):
• Slide the finger protection to
the right until it locks into place.
• Using a small amount of force,
pull the finger protection vertically
upwards and out of the openings
on the slice carriage.
Remove the slice carriage (10):
G
If necessary, unlock the slice
carriage by sliding the slice car­
riage locking device (9) to the left.
• Lift the slice carriage out of the
appliance as far as possible.
M
Press the locking latch (13)
and lift the slice carriage fully out
of the appliance.
12
Remove the rotary blade (16):
N
Fold the blade catch (15)
upwards, turn it clockwise, and
remove it.
• Take hold of the rotary blade
at its rotational centre and
remove it.
Cleaning after each use
• Wipe down the housing and
all removed parts, including the
rotary blade, with a damp cloth.
Occasional cleaning
• Give all removed parts, includ­
ing the rotary blade, a thorough
wash in warm soapy water (not in
the dishwasher!).
• Clean the housing behind the
blade using a dry cloth/brush.
Info:
Do not use any abrasive cleans-
ers, sponges with rough surfaces
or hard brushes to clean the
appliance.
• Dry all parts that you have
washed.
• Grease the rotary blade's gear
wheel with a little ritter mainte­
nance grease (alternatively with a
little Vaseline).
• Fit the rotary blade back into
the appliance.
• Slide the slice carriage back
onto its rails.
MAINTENANCE
Your food slicer is maintenance­
free. However, we recommend
that you occasionally apply a little
extra ritter maintenance grease
or Vaseline to the rails of the slice
carriage to keep them lubricated
and ensure that the carriage
continues to move easily.
STORAGE
• Slide the slice carriage (10)
into the appliance until it locks
into place.
G
Secure the slice carriage in
place by sliding the slice carriage
locking device (9) to the right.
• Remove the left­over
holder (12).
I
Remove the finger
p rotection (11):
• Slide the finger protection to
the right until it locks into place.
• Using a small amount of force,
pull the finger protection vertically
upwards and out of the openings
on the slice carriage.
• Make sure that the slice
thickness adjustment knob (3)
is set to position "0", as
otherwise the appliance can-
not be folded down for safety
reasons.
O
Press the folding up safety
fixture (6) and swivel the appli­
ance until the slice carriage is
fully in contact with the stop
plate (2).
P Q
Storing the individual parts:
• Slide the tray (5) into the
holder provided for it on the
underside of the slice carriage.
Info:
The tray can also be stored on
the underside of the slice carriage
when the appliance is open.
• Place the finger protection with
the two magnets onto the fixing
heads behind the stop plate.
• Place the left­over holder on
top of the appliance.