Bentel Security PREMIUM Serie Mode D'emploi page 7

BRIGHTNESS, CONTRAST AND VOLUME
To adjust the brightness, the contrast and the volume of the internal buzzer, follow
the procedure described below:
BRIGHTNESS
It is possible to adjust the brightness of the keys and, on the LCD version only, also
the brightness of the backlighting of the display.
It is possible to adjust the inactive and the active brightness (the inactive brightness
is the brightness to which the keypad reverts after 10 seconds of inactivity.
To adjust the active brightness, follow the procedure described below:
1a) To increase the brightness, press and keep pressed key A until the desired
level is obtained:
1b) To lower the brightness, press and keep pressed key B until the desired level
is obtained:
2) Press the OFF key to adjust the inactive brightness:
3a) To increase the brightness, press and hold down key A until the desired
brightness is reached:
3b) To reduce the brightness, press and hold down key B until the desired
brightness is reached:
4) Press the ON key to adjust the active brightness and return to step 1a), or press
the ENTER key to confirm the chosen levels, or
wait a few seconds for the keypad to return to the inactive state.
CONTRAST (only for the LCD version)
To adjust the contrast of the LCD display, follow the procedure described below:
1a) To increase the contrast, press and keep pressed key D until the desired level
is obtained.
1b) To lower the contrast, press and keep pressed key C until the desired level
is obtained.
2) To confirm the chosen level, press the ENTER key (or wait a few seconds for the
keypad to return to the inactive state).
VOLUME
To adjust the volume of the internal buzzer, follow the procedure described below:
1) Press and keep pressed the ESC key; the internal buzzer will start sounding a
series of beeps in such manner that the operator could hear the sound level in real
time.
NOTE - The buzzer will still emit a series of sound alerts at extremely low volu-
me, even if it has been set to zero.
2a) To increase the volume, press key A for a number of times and/or keep it
pressed until the desired level is obtained:
2b) To lower the volume, press più volte and/or keep pressed key B until the
desired level is obtained.
3) To confirm the chosen level, press the ENTER key (or wait a few seconds for the
keypad to return to the inactive state).
BENTEL SECURITY srl reserves the right to modify the technical specifications of this product without prior notice.
CONNECTIONS
The keypad should be connected to the BPI bus of the control panel as described
in the instructions delivered with the same control panel.
This Keypad supports ONLY a 12 V BPI level.
To connect the zones and the outputs (terminals T) refer to the control panel
installation manual.
To connect Contacts for Roller blinds refer to Fig.1: the Keypad zones in FAST mode
(Roller blind), can be programmed as Normally Closed (a), Balanced 10K (b) and
Double Balanced (c).
TAMPERING AND DISCONNECTION
When the keypad is opened or pulled off the wall, a tamper alert is generated for
all enabled and configured devices: Keypad Tamper, Motion Sensor Tamper, Input
Expansion Tamper, Output Expansion Tamper.
The keypad also generates a tamper alert every time it is activated, as follows (see
figure below):
1. if the Output Expansion is enabled, NO tamper alert is generated when the
keypad is activated;
2. if the Input Expansion is enabled, an Input Expansion tamper alert is
generated;
3. if the Input Expansion is NOT enabled, a Keypad tamper alert is generated
(if the keypad is connected to a KYO320, KYO300 or KYO100 control unit
and has been configured).
When the keypad does NOT respond to the prompts of the control unit (due to a lack
of power, problems in bus communication, mismatched addresses, general
malfunctions), a BPI Device Disconnection alert is generated for all enabled and
configured devices: Keypad Disconnection, Motion Sensor Disconnection, Input
Expansion Disconnection, Output Expansion Disconnection.
.(<3$'
32:(5 6833/<

287387
(;3$1'(5
(1$%/('"
12

,1387
(;3$1'(5
(1$%/('"
12

.(<3$'
&21),
*85('"
12
67$1'%< 67$786
<(6
67$1'%< 67$786
<(6
,1387 (;3$1'(5
7$03(5
<(6
.(<3$'
7$03(5