Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
7.
Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help. Liquid
ejected from the battery may cause irritation or
burns.
Do not use a battery pack or machine that is
8.
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
9.
Do not expose a battery pack or machine to
fire or excessive temperature. Exposure to fire
or temperature above 130°C (265°F) may cause
explosion.
10. Follow all charging instructions and do not
charge the battery pack or machine outside of
the temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside of the specified range may damage the
battery and increase the risk of fire.
11.
Have servicing performed by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the product is
maintained.
12. Do not modify or attempt to repair the machine
or the battery pack except as indicated in the
instructions for use and care.
13. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
14. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
15. Do not charge battery in rain, or in wet
locations.
16. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
17. Do not replace the battery with wet hands.
18. Do not replace the battery in the rain.
19. Do not wet the terminal of battery with liquid
such as water, or submerge the battery. Do not
leave the battery in the rain, nor charge, use,
or store the battery in a damp or wet place. If
the terminal gets wet or liquid enters inside of bat-
tery, the battery may be short circuited and there is
a risk of overheat, fire, or explosion.
20. After removing the battery from the tool or
charger, be sure to attach the battery cover to
the battery and store it in a dry place.
21. If the battery cartridge gets wet, drain the
water inside and then wipe it with a dry cloth.
Dry the battery cartridge completely in a dry
place before use.
22. Do not charge the battery outdoors.
23. Do not handle charger, including charger plug,
and charger terminals with wet hands.
Starting up the tool
1.
Make sure that there are no children or other
people within a working range of 15 meters
(50 ft), also pay attention to any animals in the
working vicinity. Otherwise stop using the tool.
2.
Before use always check that the tool is safe
for operation. Check the security of the cutting
tool and the guard and the switch trigger/lever
for easy and proper action. Check for clean
and dry handles and test the on/off function of
the switch.
3.
Check damaged parts before further use of
the tool. A guard or other part that is damaged
should be carefully checked to determine
that it will operate properly and perform its
intended function. Check for alignment of mov-
ing parts, binding of moving parts, breakage of
parts, mounting, and any other condition that
may affect its operation. A guard or other part
that is damaged should be properly repaired
or replaced by our authorized service center
unless indicated elsewhere in this manual.
Switch on the motor only when hands and feet
4.
are away from the cutting tool.
Before starting make sure that the cutting
5.
tool has no contact with hard objects such as
branches, stones etc. as the cutting tool will
revolve when starting.
Remove any adjusting key, wrench or blade
6.
cover before turning the power tool on. An
accessory left attached to a rotating part of the
power tool may result in personal injury.
Make sure there are no electrical cables, water
7.
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
Do not use a cutting tool which is not recom-
8.
mended by Makita.
Do not operate the tool in bad weather or if
9.
there is a risk of lightning.
Method of operation
1.
Only use the tool in good light and visibility.
During the winter season beware of slippery
or wet areas, ice and snow (risk of slipping).
Always ensure a safe footing.
Take care against injury to feet and hands from
2.
the cutting tool.
3.
Never cut above waist height.
4.
Never stand on a ladder and run the tool.
Never climb up into trees to perform cutting
5.
operation with the tool.
4 ENGLISH
Publicité
Table des Matières
