R&G IF0001SI Instructions page 6


The aluminium support can now be removed by un-doing the four bolts that secure the plate into
the top yoke, as shown in picture 8.

Remove the two recessed bolts that mount the ignition barrel from the rear, as arrowed in picture
9.

Take the R&G Instrument Panel Fascia (item 1) and place two M6 x 45mm Button Head Bolts
(item 4) through the two holes around the second largest hole (offset to one side) from the top
Page | 6
side, as shown in picture 10.

With the bolts protruding through to the back, place one spacer (item 5) over each bolt, then the
ignition barrel, before one washer and M6 nyloc nut on each bolt, as shown in picture 11. Ensure
it is located to the correct way around, with the symbols on the left, as shown in picture 12.

Now re-fit the instrument panel lights through the sheet metal and tighten the two small original
bolts, as shown in picture 12.

Re-fit the rubber mounts to the R&G sheet metal, ensuring the two protrusions on the rubber
locate into the cut out on the sheet metal.

The dials can now be re-fitted. Begin with the rev counter, by positioning the dial through the
rubber from the top and then re-connecting the electrical contacts and re-fitting the bulbs into
place. Once in place, re-fit the plastic cover, ensuring the cables exit cleanly from the slot, before
re-fitting the original washer and domed headed nuts, as shown in picture 13.

Repeat the same procedure for re-fitting the speedometer, ensuring the speedo drive cable goes
through the plastic cover, as shown in picture 14.

Re-fit the odometer dial plastic knob and tighten, as shown in picture 15.

Position the mounting block/spacer in place on the top yoke, covering the four holes, then align
the sheet metal above, as shown in picture 16.

Place the four M5 x 35mm Button Head Bolts through the sheet metal, mounting block/spacer and
into the top yoke, as shown in picture 17. Tighten the bolts evenly.

Route the speedo drive cable back through its cable clip and remount into speedo drive. Place the
Phillips screw back into the hole and re-tighten.

Check to ensure all the lights and dials work correctly.

Please make sure that there is sufficient clearance between the domed headed nuts on the back of
the instrument dials and the headlamp, to prevent any marks on the chromed surface.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Issue 2 10/01/2013 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G Racing
www.rg-racing.com Email: info@rg-racing.com