Falcon 1000 DF Guide De L'utilisateur page 21

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
d) Remove the tap. Remove and discard the gasket seal.
Fit new gasket seal to replacement tap.
e) Re-assemble in reverse order. Check the appliance is
gas sound. Check hotplate ignition.
9 To Change an Ignition Switch
Change the gas tap as detailed in Section 8.
10 To Remove a Hotplate Burner Injector
a) Remove the hotplate as detailed in Section 1.
b) Remove the injector directly from the burner body.
c) Fit the appropriate injector.
d) Re-assemble in reverse order. Check the appliance is
gas sound.
11 To Remove a Hotplate Burner Spark
Electrode
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Undo the bezel venturi and remove the bezel from the
hotplate. The spark ignition wire will be pulled through
the electrode clearance hole.
c) Disconnect the spark electrode from the ignition wire.
Note
Take care to prevent the ignition wire from falling back
through the clearance hole.
d) Undo the spark electrode from the bezel by removing
the spring clip and spring.
e) Fit the replacement electrode to the burner bezel.
Ensure that the spring and clip are properly located.
f) Replace in reverse order and check correct burner
ignition.
12 To Remove a Hotplate Burner
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 1.
c) Remove the nut that secures the burner body to the
support channel.
d) Remove the fi xings that secure the support channel to
the chassis. Lift the channel clear of the appliance.
e) Undo the compression fi tting which connects the
burner body to the gas pipe. Remove the burner body
from the appliance.
f) Replace in reverse order. Check the appliance is gas
sound and that the burner operates satisfactorily.
13 To Remove the Oven Door
a) Open the oven door.
b) Rotate hinge locking disc 90° clockwise on both door
hinges to lock door in open position.
c) Carefully close door and at approximately half closed
the hinges will release themselves from the cooker
frame.
d) Re-assemble in reverse order.
14 To Remove the Oven Outer Door Panel
a) Remove the door from the cooker (see section 13).
b) Remove screws holding the outer panel to the door.
c) Remove the outer door panel.
All manuals and user guides at all-guides.com
SERVICING - WARNING
21
d) Undo the nuts that secure the handle to the door
panel. Fit the handle to the replacement door panel.
e) Fit the replacement panel to the oven inner door
making sure that the door insulation is correctly
located.
f) Re-assemble in reverse order.
15 To Remove the Oven Door Seal
a) Open oven door. The seal is held in place by small
hooks on the rear face. At the corner pull seal
diagonally away from the door centre until that hook is
released.
b) Proceed to the next hook and release it in a similar
way, and so on. Use force if the hooks are stiff, as the
old seal will be discarded.
c) Hook the new seal in one of the corner holes of the
door, and proceed round the door opening snapping
in each hook in turn.
16 To Remove the Hotplate Electrode Leads
Disconnect from the electricity supply.
Pull the unit forward to access the rear of the appliance.
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 1.
c) Remove the cover box and disconnect all HT leads at
the generator.
d) Pull the sleeved bundle of HT leads up through the
rear upright.
e) Pull the appropriate lead from the sleeve and push in
the replacement.
f) Replace the leads in the rear upright.
g) Re-connect the leads at the generator.
h) Re-assemble in reverse order and check ignition.
17 To Remove Spark Generator
a) Isolate from electric supply.
b) Lower front mobility wheels (see section 'MOBILITY
WHEELS' in Users instructions) and pull cooker
forwards to gain access to the rear of the cooker.
CAUTION: DO NOT STRAIN FLEXIBLE GAS
CONNECTION disconnect if necessary.
c) Remove mains cable inlet cover, 8 screws.
d) Disconnect electric cables to generator.
e) Remove two screws securing generator mounting
bracket to cooker frame and carefully withdraw
generator suffi ciently to disconnect electrode leads.
f) Re-assemble in reverse order.