Device Description (Fig. 1, 2); Scope Of Delivery; Intended Use - Scheppach CAG115-20ProS Traduction Des Instructions D'origine

1. Introduction
Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working ex-
perience with your new machine.
Note:
According to the applicable product liability law the
manufacturer of this device is not liable for damages
which arise on or in connection with this device in
case of:
• improper handling,
• non-compliance with the instructions for use,
• repairs by third party, non authorized skilled work-
ers,
• installation and replacement of non-original spare
parts,
• improper use,
• failures of the electrical system due to the
non-compliance with the electrical specifications
and the VDE 0100, DIN 57113 / VDE 0113 regu-
lations
Recommendations:
Read the entire text of the operating instructions pri-
or to the assembly and operation of the device.
These operating instructions are intended to make it
easier for you to get familiar with your device and uti-
lize its intended possibilities of use.
The operating instructions contain important notes
on how to work safely, properly and economically
with your machine and how to avoid dangers, save
repair costs, reduce downtime, and increase the reli-
ability and working life of the machine.
In addition to the safety regulations contained herein,
you must in any case comply with the applicable reg-
ulations of your country with respect to the operation
of the machine.
Put the operating instructions in a clear plastic fold-
er to protect them from dirt and humidity, and store
them near the machine. The instructions must be
read and carefully observed by each operator prior
to starting the work. Only persons who have been
trained in the use of the machine and have been in-
formed on the related dangers and risks are allowed
to use the machine. The required minimum age must
be met.
In addition to the safety notes contained in the pres-
ent operating instructions and the special regulations
of your country, the generally recognized technical
rules for the operation of wood working machines
must be observed.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.

2. Device description (Fig. 1, 2)

1. Guard
2. Spindle locking
3. Safety switch
4. On/off switch
5. Face spanner
6. Additional handle
7. Grinding wheel
8. Battery (not included in the scope of delivery)

3. Scope of delivery

• Cordless Angle Grinder
• Additional handle
• Face spanner
• Instruction manual

4. Intended use

This machine is intended to be used as a grinder or
a cut-off tool.
Sanding, polishing, hole cutting and wire brushing
are not recommended to be performed with this tool.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment's potential hazards.
It is also imperative to observe the accident preven-
tion regulations in force in your area.
The same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
The machine may be used only with original acces-
sories and original tools of the manufacturer.
The safety, workplace and maintenance instructions
of the manufacturer as well as the dimensions speci-
fied in the technical data must be observed.