Publicité
Les langues disponibles
Les langues disponibles
Getting Started: Initial Operation
Unpacking the Model
Remove the styrofoam packaging
extremely carefully to prevent damaging
accessories and attached parts such as
handrails etc.
Initial Operation
We recommend letting the locomotive
run without a train for 30 minutes
in both directions, to properly break
it in. This will help achieve optimal
performance and longevity for the
locomotive. Of course, your model
should only be run on smooth and
perfectly clean tracks with reliable
electrical contact to all track sections.
Technical Data
Power Supply
The model should only be operated on a
pure, filtered DC power supply of 0 to 24
volts, with a capacity of at least 2 Amps
and a fast-acting fuse or circuit breaker
to protect against short circuits. Do not
use a power supply which is not in safe
and perfect working condition. (See
"Digital Decoder" section for operation
on digital power.)
Drive System
The locomotive's two trucks each contain
a robust gearbox with a powerful high-
precision can-type motor driving all axles
through a smooth gear drive.
Lighting
The model is equipped with automatic
directional headlights, using white LEDs
for a realistic appearance. The "front"
lights are illuminated according to the
travel direction.
Radius
The loco can run on a track with a
minimum recommended radius of
600 mm (23.62'').
Accessories
Digital Decoder
The model is prepared at the factory for
use with the PIKO SmartDecoder XP 5.1
Art. No. #36500. After plugging in the
decoder, the locomotive can be used on
both digital and analog layouts.
Sound Module
The model of the BR 218 is factory
prepared for the installation of the PIKO
SmartDecoder XP 5.1 Sound #36535
with original BR 218 sound. The PIKO
SmartDecoder XP 5.1 Sound #36535
comes with a full range speaker with
waterproof membrane. After installation
of the PIKO SmartDecoder XP5.1, the
locomotive can be used with all its
digital functions on digital layouts. When
used on analog layouts, only the driving
noise of the locomotive is reproduced.
Maintenance
Lubrication
After each 25 hours of operation, and
after any long periods of storage, please
lubricate the loco's gears with a sparing
amount of plastic-compatible, non-
hardening grease. Remove the gearbox
bottom cover and be careful to keep the
front and rear wheelsets aligned with each
other. Be sure to securely re-tighten the
gearbox bottom cover screws.
Cleaning
If cleaning is necessary, use only a mild
cleaning agent (such as soap and water)
and gentle action with a soft non-abrasive
cloth or brush. Never immerse the loco in
liquid or "flood" any internal parts!
Wheel wipers and pick-up shoes should be
changed after 500 hours of operation.
Please Note!
Damage to Carpets and Other
Surfaces: Normal operation of the
loco causes wear of mechanical parts
(wheels, electrical pickups etc.). This
produces carbonized dust, grease
and oil, which can permanently
stain carpets, wood floors and other
materials. It is the user's responsibility
to take proper precautions against
this damage. Wipe any grease or oil
from the track rails with a clean soft
cloth. PIKO Spielwaren GmbH, as well
as its representatives, distributors and
retailers, assume no liability for any
such damage.
Important Safety Precautions
• Check the power supply regularly for
any damage or problems.
• Do not use a malfunctioning or
damaged power supply!
• This model must only be operated with
one power source per circuit!
• This product is not a toy, not suitable for
personnel under 14 years of age. This
product has small parts, sharp parts, and
moving parts.
• This model must only be operated with
a safety-assured power supply with the
identification!
• The power supply is not a toy!
• Disconnect the model from the power
supply before cleaning or servicing!
• Do not insert the track power connecting
wires into household "mains" voltage
outlets.
5
Publicité
