Mounting - Morningstar EcoPulse EC-10 Manuel De L'utilisateur

If the system voltage DIP Settings Switches are set
to Auto-detect, battery voltage over 15.5V will be
detected as a 24V nominal battery, and the unit will
charge accordingly.
The 12/24V auto selection is done only at start-up,
and the detected system voltage will never change
during operation. It is recommended to set DIPs 2
and 3 to the correct system voltage setting. Only use
the default auto-detect setting if the nominal system
voltage is not known.
Switches 4, 5, 6: Battery Type Selection
Preset EcoPulse battery charging options are shown
in table 3-1 below. All voltage settings listed are
for nominal 12 Volt batteries. Multiply the voltage
settings by two (2) for 24 Volt systems.
NOTE: These settings are general guidelines for use
at the operator's discretion. Consult the battery
manufacturer for optimal battery charge settings.
DIP
Absorp. Float Equalize
Switch Battery
Stage Stage Stage
Settings Type
(volts) (volts) (volts)
4-5-6
off-off-off 1 - Sealed* 14.00 13.50
off-off-on 2 - Sealed* 14.15 13.50 14.40
off-on-off 3 - Sealed* 14.30 13.50 14.60
off-on-on 4- AGM/Flooded 14.40 13.50 15.10
on-off-off 5 - Flooded 14.60 13.50 15.30
on-off-on 6 - Flooded 14.70 13.50 15.40
on-on-off 7 - L-16 15.40 13.40 16.00
on-on-on 8 - Custom Custom Custom Custom
* "Sealed" battery type includes gel and AGM batteries
Table 3.1. Battery charging settings for each selectable battery type
10
Installation
Absorp. Equalize Equalize Equalize Equalize Equalize
Equalize Equalize
Time Time Timeout Interval LVD LVR
Interval Interval
(volts) (volts)
(mins) (mins) (mins) (days)
(days) (days)
150
11.50 12.60
150 60 120 28
11.30
12.80
150 60 120 28 13.00
11.50
180 120 180 28 11.70 13.20
180 120 180 28
11.90 13.40
180 180 240 28
12.10 13.60
180 180 240 14 12.30 13.80
Custom Custom Custom Custom Custom Custom Custom Custom Custom
Switch 7: Battery Equalization
Mode
Manual Equalization
Auto Equalization
NOTE: Regardless of DIP 7 setting, manual EQ can be initiated using
the on-board meter command, "Start Equalize". For non-meter
versions, DIP 7 only enables or disables auto equalization - manual EQ
is not available.
Switch 8: Current Switching
Mode
PWM switching
Slow switching
The default (PWM) switching setting (OFF / down) operates
at 300Hz. If load or system noise is an issue, DIP 8 can be set
(ON-up) for slow switching at 1Hz. Standard PWM switching is
recommended when system noise is not a problem.

3.3 Mounting

Inspect the controller for shipping damage. Mount the
EcoPulse to a vertical surface (4-#8 zinc-plated self-
tapping screws are included). Tighten the mounting
screws using care not to crack the plastic case. Do not
install directly over an easily combustible surface since
the heat sink may get hot under certain operating
conditions.
NOTE: The heat sink must be in a vertical
position (fins up and down).
EcoPulse Operator's Manual
Switch 7
OFF
ON
Switch 8
OFF
ON
11