Télécharger Imprimer la page

DeWalt DCLE34031 Traduction De La Notice D'instructions Originale page 28

Masquer les pouces Voir aussi pour DCLE34031:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 46
EngLIsH
Congratulations!
You have chosen a D
WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Light Source
Laser diodes
Laser Wavelength
510 – 530 nm visible
Laser Power
≤1.50 mW (each beam)
CLASS 2 LASER PRODUCT
Working Range
40 m
100 m with detector
Accuracy (Plumb)
±3.1 mm per 9 mm
Accuracy (Level)
±3.0 mm per 10 mm
Battery Low
Laser beams flash with 3 quick pulses
Continuous Flashing
Tilt range exceeded/unit is not level
Laser Beams
Environmental
Water & Dust Resistant to IP54. Applies to
product, not battery or charger.
Intended Use
The DCLE34031 3x360 Laser is a Class 2 laser product. It is a
self‑leveling laser tool that can be used for horizontal (level) and
vertical (plumb) alignment projects.
DO nOT use under wet conditions or in presence of flammable
liquids or gases.
DO nOT let children come into contact with this tool.
Supervision is required when inexperienced operators use
this tool.
a
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.

DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.

Denotes risk of electric shock.
26
WALT one of the
e
DCLE34031

Denotes risk of fire.
General Safety Warnings

WARNING: Never modify the tool or any part of it.
Damage to the laser or personal injury could result.

WARNING: Read and understand all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS

WARNING: Laser Radiation Exposure. Do not
disassemble or modify the laser level. There are
no user serviceable parts inside. Serious eye injury
could result.

WARNING: Hazardous Radiation. Use of controls
or adjustments or performance of procedures other
than those specified herein may result in hazardous
radiation exposure.

CAUTION: Keep fingers clear of the back plate and
stud when mounting with magnets. Fingers may
become pinched.

CAUTION: Do not stand underneath the laser when it is
mounted with the magnet bracket. Serious personal injury
or damage to the laser may result if the laser falls.
If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment
may be impaired.
Do not operate the laser in explosive atmospheres, such
as in the presence of flammable liquids, gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
Use the laser only with the specifically designated
batteries. Use of any other batteries may create a risk of fire.
Store idle laser out of reach of children and other
untrained persons. Lasers are dangerous in the hands of
untrained users.
Tool service MUST be performed by qualified repair
personnel. Service or maintenance performed by unqualified
personnel may result in injury. To locate your nearest D
service centre go to www.2helpU.com.
Do not use tool if switch does not turn it on or off. Any tool
that cannot be controlled with the switch is dangerous and
must be repaired.
Do not use optical tools such as a telescope or transit to
view the laser beam. Serious eye injury could result.
Do not place the laser in a position which may cause
anyone to intentionally or unintentionally stare into the
laser beam. Serious eye injury could result.
Do not position the laser near a reflective surface which
may reflect the laser beam toward anyone's eyes. Serious
eye injury could result.
Turn the laser off when it is not in use. Leaving the laser
on increases the risk of staring into the laser beam. Do not
modify the laser in any way. Modifying the tool may result in
hazardous laser radiation exposure.
WALT
e

Publicité

loading