General Overview - ProMariner ProSportHD6 Manuel D'utilisation

Safety Instructions
7
Charger Location & DC Connection
14. CHARGER LOCATION
CAUTION
a. Locate charger as far away from batteries as possible.
b. Never place a charger directly above a battery being charged; gases or fluids from battery
will corrode and damage charger.
c. Do not operate charger in an enclosed area or in an area with restricted ventilation in any way.
d. Never allow battery acid to drip on charger when reading electrolyte specific gravity
or filling a battery.
e. Do not set a battery on top of charger.
f. Do not install on or over combustible surfaces.
15. DC CONNECTION PRECAUTIONS
CAUTION
a.Connect and disconnect DC output cables only after removing AC cord from electric outlet.
Never allow cables to touch each other.
IMPORTANT NOTICE: FCC CLASS B PART 15 NOTIFICATION
Your On-Board Marine Battery Charger has been designed and tested to comply with FCC Class B part
15. These regulations are to provide adequate protection against harmful interference while operated
in a commercial application. If in a residential setting, you are encountering interference with TV and
radio reception, simply remove AC power from the ProMariner unit to confirm if your battery charger
is causing interference. End user can explore the following to minimize interference:
1) Chose a different AC circuit to power your On-Board Marine Battery Charger.
2) Make sure your outlet is properly grounded.
3) Re-position receiving antenna.
4) Purchase a separate AC line filter.
5) Relocate charger so that it is at the furthest point from home receiving equipment,TV, radio, etc.

General Overview

The all new ProSportHD Generation 4 boasts a new aggressive heavy duty tri-surface heatsink
design.This new lightweight design delivers significantly faster charging through optimal
cooling, while delivering true rated constant current charging amps during charge
mode.ProSportHD's enhanced microprocessor and software control sports a dashboard of
new digital features including: fuel gauge style Charge Completion Monitor, Charge Mode
LED bar, individual dual mode Full / Fault Battery indicators and 3 digitally selectable
performance charge profiles for Flooded (lead acid), AGM and GEL batteries. HP AGM profile
on ProSportHD20 Dual only.
The new fuel gauge style Charge Completion Monitor indicates charge level progress during
operation with a single red LED indicating low battery(s) are being charged. Dedicated dual
mode battery indicators eliminate time consuming troubleshooting and clearly indicates
individual battery wiring faults, or if a battery is less than 2.5 VDC and cannot accept a
charge, when red. When green the battery is full and being monitored off line.
Distributed-On-Demand ™ Technology automatically senses and distributes 100% of available
charging amps to any one bank or combination of all banks. All unused charging amps are
Distributed-On-Demand ™ to batteries on board requiring additional charging amps.
Fully automatic multi-stage charging enhances battery performance while extending battery
life with 5 sequential stages: Analyzing, Charging, Conditioning, Auto Maintain (Energy Saver)
and a once a month storage recondition mode that is safe for short and long term storage.
System Check OK and Battery Status indicators provide real time installation and battery
fault status feedback, eliminating time consuming troubleshooting.
Energy Saver Mode: after fully charging and conditioning batteries, ProSportHD will monitor
and auto maintain batteries only when needed to maintain a full state of charge. This
significantly reduces AC power consumption and lowers operating costs while maximizing
battery performance.
Designed for use in harsh environments ProSportHD is 100% waterproof and up to 40%
lighter than traditional expoxy filled chargers. ProSportHD utilizes industrial grade jacketed
DC and AC power cables which include new molded strain reliefs and wire splitters. Listed
and certified to UL Marine 1236 SB, new energy efficient CEC (California Energy Commission)
and DOE (Department of Energy) requirements and complies with FCC Class B. 3 Year
warranty with built-in safety features including dual inline waterproof fuses, reverse polarity,
over-temperature,over-current, over-voltage and ignition protection.
General Overview
8