General Overview - ProMariner ProSport6 Mode D'emploi

Masquer les pouces Voir aussi pour ProSport6:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

S A F E T Y I N S T R U C T I O N S
7
Charger Location & DC Connection
17. CHARGER LOCATION
CAUTION
a.Locate charger as far away from batteries as possible.
b. Never place a charger directly above a battery being charged; gases or fluids from battery
will corrode and damage charger.
c. Do not operate charger in an enclosed area or in an area with restricted ventilation in any way.
d. Never allow battery acid to drip on charger when reading electrolyte specific gravity
or filling a battery.
e.Do not set a battery on top of charger.
f. Do not install on or over combustible surfaces.
18. DC CONNECTION PRECAUTIONS
CAUTION
a.Connect and disconnect DC output cables only after setting any charger switches to "off"
position and removing AC cord from electric outlet. Never allow cables to touch each other.
IMPORTANT NOTICE: FCC CLASS A PART 15 NOTIFICATION
Your On-Board Marine Battery Charger has been designed and tested to comply with FCC Class A part
15. These regulations are to provide adequate protection against harmful interference while operated
in a commercial application. If in a residential setting, you are encountering interference with TV and
radio reception, simply remove AC power from the ProMariner unit to confirm if your battery charger
is causing interference. End user can explore the following to minimize interference:
1) Chose a different AC circuit to power your On-Board Marine Battery Charger.
2) Make sure your outlet is properly grounded.
3) Re-position receiving antenna.
4) Purchase a separate AC line filter.
5) Relocate charger so that it is at the furthest point from home receiving equipment,TV, radio, etc.

General Overview

The ProSport Charger is an advanced electronic and fully automatic multi-stage on-board marine
battery charger. ProSport is pre-wired for easy installation and is 100% waterproof for fresh and
salt water applications. ProSport's multi-stage charging process delivers five modes of operation
that include: start up diagnostics, charging, conditioning, auto maintain and storage reconditioning
of each battery. This process is proven to extend the life of your batteries and will fully charge
your batteries each time you connect to AC power. ProSport delivers increased power and
performance while providing improved durability and heat transfer.
The ProSport Distributed-On-Demand
Charging Technology will automatically sense and distribute
100% of the available charging output of 8,12, 15 or 20 amps (model specific) to any one battery
or combination of all batteries. Each battery charger output is fully isolated. ProSport's easy to view
LED indicators will provide at a glance status of: AC power, battery type, charging, and ready status.
The LED status center also includes an indication of a fault or failure detected at each battery that
is connected to the charger and can be seen on the top of the unit when installed.
Note: ProSport On-Board Marine Battery Chargers are designed for any combination of group
24,27,30 and 31 batteries. Each battery charger DC output cable must be connected to one (1)
12 Volt DC battery (even if batteries are configured for 24 Volt DC or 36Volt DC trolling motor or
system applications).
Important: The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.
Each charger cable must
be connected to 1 battery,
just as shown. Observe
cable jacket
black to (-) and red to (+).
Do this for each battery.
When connecting to an engine start battery only connect the battery bank cable that is LABELED:
"FOR ENGINE BATTERY, USE THIS BANK CABLE ONLY".
Application Tip
If your application is for 4D or 8D large capacity batteries, please refer to ProMariner's website
www.promariner.com and view our ProNauticP Hardwired Charger Assortment for a model that
is correct for this group size of batteries.
Most specifically you do not have to remove series or parallel jumper cables to use your ProSport
charger. See typical wiring diagrams for these systems in the installation section of this manual.
Note: The ProSport must be connected to batteries to operate. It will not operate as a
12 volt power supply.
G E N E R A L O V E R V I E W
black (-)
Group size 24
thru 31 only
red (+)
8

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Prosport8Prosport12Prosport15 oemProsport20Prosport20 plus43006 ... Afficher tout

Table des Matières