Connecting The Battery - XciteRC X-PERT X90T Mode D'emploi

LCD Contrast
Button Sound
Buzzer Sound
Max Out Watt
BACK
save and back
U S E R S E T U P (2/5)
Input Cut
EN
Safety Timer
Int.Cut-Off
Temp.Cut-Off
Max Out CAPA
BACK
U S E R S E T U P (3/5)
Nixx Cycle Mode
Nixx Cycle Cnt
Cycle Wastertime
NiMH DeltaV
NiCd DeltaV
BACK
U S E R S E T U P (4/5)
LiPo CHG
LiPo DCHG
LiFe CHG
LiFe DCHG
PB CHG
BACK
U S E R S E T U P (5/5)
PB DCHG
NiMH DCHG Cut
NiCD DCHG
LiIo CHG
LiIo DCHG
BACK

Connecting the battery

NiMH or lead acid batteries (Pb): first plug the charging cable into the 4 mm sockets on the side of the
charger. Now connect the battery.
Lithium batteries: Connect the Balancer adapter to the charger - the socket is polarized, pay attention
to the side guides. Then connect the charging cable to the 4 mm sockets on the side of the charger. Now
connect the battery to the balancer adapter and charging cable.
• WARNING: Use only batteries with XH balancer plugs. Never try to connect other plug types with
the charger! The plug or charger may damage or worse, the battery catches fire or explodes! If
necessary, use a suitable adapter cable.
• WARNING: The socket is polarized. The balancer plug must fit easily, do not use force! The plug
could be damaged or worse, the battery catches fire or explodes!
• WARNING: Before charging make sure check the type of the battery. Lithium batteries with more
than one cell must always be charged with attached Balancer in Mode BCHG- fire hazard!
• Note: 1S lithium batteries have no extra balancer connector!
24
:
40
:
ON
:
ON
:
80W
NEXT
:
10.0V
:
240min
:
80
℃
:
60
℃
:
10.1AH
NEXT
:
C->D
:
2 T
:
5Min
:
7mv
:
10mv
NEXT
:
Cut 4.20V
:
Cut 3.20V
:
Cut 3.60V
:
Cut 2.00V
:
Cut 2.40V
NEXT
:
Cut 1.50V
:
1.00V
:
Cut 0.80V
:
Cut 4.10V
:
Cut 3.10V
NEXT
LCD Contrast
Button sound
Buzzer sound
Max. Output power
increase value
decrease value
Input low voltage cut-off
Safety timer
Internal cut-off temperature
Battery cut-off temperature
Max. capacity
NiXX Cycle mode
Cycle count
Pause between the cycles
NiMH ∆P
NiCd ∆P
LiPo end-of-charge voltage
LiPo end-of-discharge voltage
LiFe end-of-charge voltage
LiFe end-of-discharge voltage
Pb end-of-charge voltage
Pb end-of-discharge voltage
NiMH end-of-discharge voltage
NiCd end-of-discharge voltage
LiIo end-of-charge voltage
LiIo end-of-discharge voltage
30 - 60
on / off
on / off Connecting the battery
80 - 80 W
10.0 - 18.0 V
10 - 600 min.
50 - 80°C
50 - 80°C
500 mAh - 50 Ah
C (charge) -> D (discharge) / D -> C
1 - 5 Mal
5 - 60 Min.
5 - 25 mV
5 - 20 mV
4.00 - 4.25 V
3.00 - 4.00 V
3.50 - 3.70 V
1.80 - 3.30 V
2.00 - 2.50 V
1.20 - 2.00 V
0.80 - 1.50 V
0.50 - 1.50 V
4.00 - 4.15 V
3.00 - 3.90 V
X-pert Charger X90T