Memory Storing The Radio Code; Memory Storage Of 868 Mhz Radio Controls; Memory Storage Of 433 Mhz Radio Controls - Genius LYNX 06/230V Mode D'emploi

The control unit has an integrated 2-channel decoding system. The system makes it possible to memory store - via the
receiver module - both the OPEN/CLOSE command and the CLOSE command.
The decoding system makes it possible to memory store both the radio controls with a frequency of 868 MHz and the
radio controls with a frequency of 433 MHz.
Only one radio code can be used at a time. To change over from one code to the other, delete the existing radio
code (see paragraph 7.3), replace the receiver module and repeat the programming stages.
Fitting and, if necessary, removing the receiver module must be done only after cutting power to the board.
The receiver module can only be inserted in one position. Orient the module correctly without forcing.

7.1. MEMORY STORAGE OF 868 MHz RADIO CONTROLS

Before you save the radio control, we advise you to run a deletion procedure – see paragraph 7.3.
You can memory store up to a maximum of 250 codes, subdivided between the two channels, OPEN/CLOSE and
CLOSE.
1. On the radio control, simultaneously press and hold down push-buttons P1 and P2 (see radio control instructions).
After about one second, the LED of the radio control begins to flash.
2.
3. Release both push-buttons.
4. Press and hold down push-button P3 or P4 on the board, according to the input you wish to save (input of OPEN/
CLOSE or CLOSE). When the relevant LED begins to flash - release the push-button.
5. Simultaneously press the push-button of the radio control with which you wish to associate the selected
command.
6. Check if the LED relating to the command being memory stored (DL7 for the OPEN/CLOSE channel or DL8 for the
CLOSE channel) lights up on steady beam for about two seconds to confirm correct memory storage.
7. To finish programming, press twice in close succession, the push-button of the memory stored radio control.
The automated system will perform an opening manoeuvre - make sure that there are no obstacles inside the
operating range.
8. To memory store the other channel, repeat all the procedure from point 1.
To add other radio controls, transfer the code of the memory-stored push-button of the radio control to the relevant
push-button of the radio controls to be added, repeating the memory storage procedure or observing the following
procedure:
On the memory stored radio control, simultaneously press and hold down push-buttons P1 and P2 (see radio control
•
instructions).
• The radio control LED begins to flash.
• Release both push-buttons.
• Put the two radio controls frontally into contact.
• On the memory stored radio control, press and hold down the push-button relating to the channel you wish to transfer
- the radio control LED lights up on steady beam.
On the radio control to be memory stored, press the required push-button and release it after the radio control has
•
flashed twice.
• To finish programming, press twice in close succession, the push-button of the memory stored radio control.
The automated system will perform an opening manoeuvre - make sure that there are no obstacles inside the
operating range.

7.2. MEMORY STORAGE OF 433 MHz RADIO CONTROLS

Before you save the radio control, we advise you to run a deletion procedure – see paragraph 7.3.
You can memory store up to a maximum of 250 codes, subdivided between the two channels, OPEN/CLOSE and
CLOSE.
1. On the control unit, press the push-button of the channel you wish to memory store, P3 for the OPEN/CLOSE channel
or P4 for the CLOSE channel.
2. The relevant LED on the control unit begins to flash - release the push-button.
3. On the radio control, press the push-button with which you wish to associate the selected channel.
4. The LED on the control unit lights up on steady beam for about one second, signalling that the radio control was
stored in the memory, then it resumes flashing.
5. During this stage further radio controls can be stored in the memory.
6. After about 10 seconds, the control unit automatically exits the learning stage.
To add other radio controls or memory store the second channel, repeat the operations from point 1
7.
7.2.1. R
EMOTE MEMORY STORAGE OF
Other radio controls can be remotely stored only with the 433 radio controls, i.e. without using the push-buttons of the
control unit, but using a previously stored radio control.
1. Get a radio control already memory stored on one of the 2 channels.
2. Step near to the automated system.
3. Press and hold down push-buttons P1 and P2 (see radio control instructions) simultaneously for about 5 seconds.
Within 5 seconds, press, on the memory stored radio control , the push-button you wish to transfer to the new radio
4.
control. In this way the learning stage on the selected channel is activated on the control unit.

7. MEMORY STORING THE RADIO CODE

433 MH
Z RADIO CONTROLS
21