Memory Storing The Radio Code Page; Memory Storage Of 868 Radio Controls; Memory Storage Of 433 Radio Controls; Radio Controls Deletion Procedure - Genius BRAIN 13 Mode D'emploi

8. MEMORY STORING THE RADIO CODE
The control board has an integrated 2-channel decoding system. This sy-
stem makes it possible to memory-store both total opening (OPEN A) and
partial opening OPEN B) of the automated system - this is made possible
by an additional receiver module (fig.3 ref. a) and radio controls on the
same frequency.
• Only one radio code can be used at a time.
• To change over from one code to another, you must delete the
existing one (see paragraph on deletion), and repeat the memory-
storage procedure.

8.. MEMORY STORAGE OF 868 RADIO CONTROLS

A maximum of 250 codes can be memory stored, split between
OPEN A and OPEN B.
1. On the radio control, simultaneously press and hold down push-buttons
P1 and P2.
2. The radio control LED begins to flash.
3. Release both push-buttons.
4. Press the LOGIC (SW3) or SPEED (SW2) push-button, to memory store
respectively total opening (OPEN A) or partial opening (OPEN B), and as
you hold it down, also press the SETUP (SW1) push-button. The relevant
LED starts to flash slowly for 5 sec.
5. Release both push-buttons.
6. Within these 5 sec., while the radio control LED is still flashing, press and
hold down the required push-button on the radio control (the radio
control LED lights up on steady beam).
7. The LED on the board lights up on steady beam for 1 second and then
goes OFF, indicating that storage was executed.
8. Release the radio control push-button.
9. Quickly press twice the memory stored radio control push-button.
The automated system performs one opening operation. Make sure that
the automated system is free of any obstacle created by persons or
things.
To add other radio controls, transfer the code of the memory-stored push-
button of the radio control to the relevant push-button of the radio controls
to be added, observing the following procedure:
• On the memory stored radio control, simultaneously press and hold down
push-buttons P1 and P2.
• The radio control LED begins to flash.
• Release both push-buttons.
• Press the memory stored push-button and hold it down (the radio control
LED lights up on steady beam).
• Bring the radio controls near, press and hold down the push-button of the
radio control to be added, releasing it only after the double flash of the
radio control LED, which indicates memory storage executed.
• Quickly press twice the push-button of the memory stored radio control.
The automated system performs one opening operation. Make sure that
the automated system is free of any obstacle created by persons or
things.

8.2. MEMORY STORAGE OF 433 RADIO CONTROLS

A maximum of 250 codes can be memory stored, split between
OPEN A and OPEN B.
1. Use 433 remote controls only with receiver module at 433 MHz.
2. Press the LOGIC (SW3) or SPEED (SW2) push-button, to memory store
respectively total opening (OPEN A) or partial opening (OPEN B), and as
you hold it down, also press the SETUP (SW1) push-button. The relevant
LED starts to flash slowly for 5 sec.
3. Release both push-buttons. Within these 5 sec., press the appropriate
push-button on the remote control.
4. The LED lights up on steady beam for 1 second, indicating memory
storage executed, and then resumes flashing for another 5 sec., during
which another radio control (point 4) can be memory stored.
5. When the 5 sec. have elapsed, the LED goes OFF indicating the end
of the procedure.
6. To add other radio controls, repeat the operation at point 1.
8.2.1. REMOTE MEMORY STORAGE OF 433 RADIO CONTROLS
Other radio controls can be remotely stored only with the 433 radio controls,
i.e. without using the LOGIC-SPEED-SETUP push-buttons, but using a previously
stored radio control.
1. Get a radio control already stored on one of the 2 channels (OPEN A
or OPEN B ).
2. Press and hold down push-buttons P1 and P2 simultaneously until both
the LEDs flash slowly for 5 sec.
3. Within 5 sec. press the push-button of the radio control that had been
memory stored to enable learning on the selected channel.
4. The LED on the board relating to the channel being learned flashes for
5 sec., within which time the code of another radio control must be
transmitted.
5. The LED lights up on steady beam for 2 seconds, indicating memory
storage executed, and then resumes flashing for 5 sec., during which
other radio controls can be memory stored, and then goes OFF.

8.3. RADIO CONTROLS DELETION PROCEDURE

To delete ALL the input radio control codes, press push-button LOGIC (SW3)
or SPEED (SW2) and, while holding it down, also press push-button SETUP
(SW1) for 10 sec.
1. The LED relating to the pressed push-button flashes for the first 5 sec, and
then flashes more quickly for the next 5 sec.
2. Both LEDs light up on steady beam for 2 sec and then go OFF (deletion
completed).
3. Release both push-buttons.
This operation is NOT reversible. All codes of radio controls stored as
Fig. 3 Fig. 3
OPEN A and OPEN B will be deleted.
9. BATTERY KIT (OPZIONAL)
The buffer battery kit was built for insertion inside the control board sup-
port.
This support (Fig. 4 ref. a) was pre-moulded to permit the battery housing
to be opened.
1. Remove the board support material covering the battery housing, cutting
the material connections along the perimeter.
2. Insert the battery in the housing you have just created, and secure it on
the anchoring supports (Fig. 5).
3. To correctly fasten and connect the kit to the control unit, consult the
instructions enclosed with the battery kit.

0. AUTOMATED SYSTEM TEST

When you have finished programming, check if the system is operating
correctly. In particular, check if the safety devices are operating correctly.

Fig. 5 Fig. 5
Fig. 4 Fig. 4