steute RF I/O SW868-NET Instructions De Montage page 3

RF I/O SW868/SW915/SW917/SW922-NET
//
Montage- und Anschlussanleitung / Funk-Universalsender
Mounting and wiring instructions / Wireless universal transmitter
Instructions de montage et de câblage / Émetteur universel sans fil
Istruzioni di montaggio e collegamento / Trasmettitore universale wireless
Instruções de montagem e instalação / Transmissor universal sem fio
Инструкция по монтажу и подключению / Универсальный радио-передатчик
English
External devices
The sensor/switch connection is led out at the four M12 connectors.
Connect the external devices to M12 (with connecting cable 1215497).
To connect external devices (sensors or switches): see section
»Connecting external devices«.
When installing the external device, follow its installation instructions.
Connectable devices:
Device
0.3 m
RF IS M8 nb-ST
RF IS M12 nb-ST
RF IS M18 nb-ST
RF IS M30 nb-ST
RF RC 20 1S-ST 1335490
connecting cable,
open wire ends
Note:
- External switches (devices) must be suitable for the specified switch-
ing capacity (3 V DC/0.3 mA at the moment of switch-on). The switch-
ing capacity ensures a long battery life. Switches with gold contacts
and reed switches are suitable.
- Always use the specified connecting cable to connect external devic-
es. Only suitable for load-free external devices.
- In the event of a short circuit using the connecting cable 1215497, the
battery will discharge.
In this case: Replace the battery.
Design of wireless range
The radio signal is attenuated on the way from the transmitter to
the receiver. In addition, the radio signal is attenuated/influenced by
obstacles. The degree of attenuation depends on the material of the
obstacle. The following tables serve as a guide.
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Material No. (Cable length)
0.5 m 1 m 2 m
1470040 1373082 1305745
1228522 1356467 1189974
1261564 on request 1189975
1260490 1228548 1189976
1215497
Penetration
90...100%
65...95%
10...90%
0...10%
Typical ranges:
Place of use
in free field (SW868/915/917)
in free field (SW922)
indoors (SW868/915/917)
indoors (SW922)
Field strength meter for range test:
Transmitter Device
SW868 swView 868 MHz
SW915 swView 915 MHz
SW917/SW922
Radio operation
The transmission of a switching command from the transmitter to the
receiver takes about 80 to 100 ms, based on the sWave® data trans-
mission. The switching signal of a transmitter may not be generated at
a shorter distance, otherwise this signal will be overlooked. The re-
ceiver must conform to the sWave.NET® protocol of the steute mod-
ules. Each switching operation triggers a transmission from the radio
unit. This also applies if several channels are activated or deactivated
simultaneously. The current value of the battery voltage is transmitted
with each transmission.
Allocation of locations and radio frequencies:
Device type Radio frequency
SW868 868.3 MHz
SW915 915.0 MHz
SW917 917.0 MHz
SW922 916.5 MHz
Battery
Variants with battery included in delivery:
Name
RF I/O SW868-4E-2,2Ah
RF I/O SW868-4E-2,2Ah RS Components
RF I/O SW915-4E-2,2Ah
The delivery includes a lithium battery SL-760/S 3.6 V/2.2 Ah (AA).
Observe that the insulation strip must be removed in order to activate
the lithium battery.
To replace the battery: see section »Battery replacement«.
3 / 24
Wireless range
(approx.)
450 m
150 m
40 m
20 m
Material No.
1190393
1221794
on request
Place of use according to
EU 2014/53/EU (RED)
USA FCC
Canada IC
Mexico IFT
Brazil ANATEL
Japan ARIB STD-T108
Material No.
1359762
1459212
1362074