Télécharger Imprimer la page

Skil 7420 Notice Originale page 7

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 9
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
This tool should not be used by people under the age of
16 years
This tool is not suitable for wet sanding
Never use the tool when cord is damaged; have it
replaced by a qualified person
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Regularly clean the power tool's air vents (the
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards)
Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
SKIL can assure flawless functioning of the tool only
when original accessories are used
Do not continue to use worn, torn or heavily clogged
sanding sheets
BEFORE USE
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
The noise level when working can exceed 85 dB(A); wear
ear protection
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
When sanding metal, sparks are generated; do not
use dust bag and keep other persons and combustible
material from work area
DURING USE
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
Do not touch the moving sanding disc
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
Backing pads
- never run the tool without backing pad A
! replace damaged backing pads immediately
(loosen/fasten 4 pad screws B)
! unplug tool before removing/mounting backing
pads
Mounting of sanding sheet 6
- mount VELCRO sanding sheet C as illustrated
- if necessary, clean backing pad first
! perforation in sanding sheet should correspond
with perforation in sanding foot
! the dust suction requires the use of perforated
sanding sheets
! replace worn sanding sheets in time
Dust suction 7
- mount dust bag D
- empty dustbag regularly for optimal dust pick-up
performance
! do not use dust bag when sanding metal
On/off
- before switching on the tool, you should place it with
the entire sanding surface on the workpiece
- when switching on, do not apply too much pressure on
the tool
- switch on/off the tool by pushing switch E 2 in "I"/"O"
position
! be aware of the sudden impact when the tool is
switched on
! before switching off the tool, you should lift it from
the workpiece
7

Publicité

loading

Ce manuel est également adapté pour:

F0157420