Connections; Normal Play - Denon DCM-65 Mode D'emploi

CONNECTIONS

(1) Connecting the Output Terminal
• Connect one end of the connection cord supplied with the CD Player to
the output terminals, left (L) and right (R) of the CD Player, and the other
end to the CD, AUX or TAPE PLAY input terminals, left (L) and right (R), of
the amplifier.
DCM-65/35
IN OUT COAXIAL
SYN HRO ONTROL D GI AL OU
E OUT
ARIA LE
(Amplifier)
SIGNAL
GND
SPEAKER SYSTEMS
R
NPUTS PB REC
PHONO CD TUNER AUX TAPE 1 TAPE 2 TAPE 1 TAPE 2
/DAT /MD /DAT /MD
L L
R
(2) Connecting the Digital Output Jack (COAXIAL) (DCM-65 only)
• Use a 75 Ω/ohm pin cord to connect the digital output jack (COAXIAL) of
the DCM-65 to the digital input jack (COAXIAL) on a digital processor or
MD recorder, available in stores.
DCM-65/35
N OUT COAX AL
YNCHRO CONTROL D G TAL OUT
LINE OUT
VAR ABLE
Digital processor or MD recorder
D GITAL INPUT
COAX AL
OPT CAL

NORMAL PLAY

Follow the steps below to get an understanding of the disc play
procedure.
(1) Starting Playback
HD D
PCM AUD O TEC NOLOGY CD UTO CHANG R DCM 65
T ACK
‚⁄
EM TE
EN OR D SC M N
¤ ‚‹ fi‚
5 DISC AUTOMATIC DISC LOAD NG SYSTEM
£
ON FF
PHON S
1. Turn the power switch on and press the open/close (
button to open the drawer.
2. Set the disc to be played in the front side tray.
1
3. Press the play button ( ).
4. The drawer closes and the disc just loaded is played.
5. The disc number, track number and elapsed time, etc., for the disc
currently playing appear on the display window.
5
6. If the open/close ( OPEN/CLOSE) button is pressed while a disc is
playing, playback continues, but the drawer opens and four discs can be
replaced. The disc that can be replaced switches when the DISC SKIP
button is pressed.
5
Press the open/close ( OPEN/CLOSE) button again to close the drawer.
Power supply outlet
L
A
B
AC OUTLET
Power supply outlet
TOP PAUSE P AY
REPEAT PROG
1 2 3 4
EC 5 6 7 8
9 101 12
3141 16
OP N CLO E D S
( 1 PLAY )
5
OPEN/CLOSE)
(3) SYNCHRO Jack Connections
• Connect the SYNCHRO jack with a DENON cassette deck which is
equipped with a SYNCHRO jack, then make a synchronized recording. Use
the connection cord supplied with the cassette deck.
• To make use of this function, also connect the output jacks and make the
settings so that a recording can be made from the CD player to the
cassette deck.
DCM-65/35
N OUT COAX AL
SYNCHR CONT OL DIG TAL OUT
L NE OUT
VAR AB E
(Cassette Deck)
(2) Stopping Playback
H CD
CM UD O ECHNO OGY / CD AUTO CH NGER DCM 65
TRA K
R MOTE ‚⁄
S NS R D SC
¤
5 DISC AUTOMATIC DISC LOADING SYSTEM
ON £ O F
HONES
2
1. Press the stop button ( STOP) to stop playback.
2. To replace discs, press the open/close (
The disc which was playing switches over to the front side and the drawer
opens.
• Set the disc you want to
played in the front side.
CM AU IO T CHN LOGY CD AU O CHA GER
ON £ FF
HON S
Power supply outlet
STOP P USE PLAY
RE EAT ROG
1 2 3 4
M N SEC 5 6 7 8
‚‹ fi‚
9 1 1112
131 1516
PEN C OSE D SC K P
( 2 STOP )
5
OPEN/CLOSE) button.
H CD
S OP
DCM 65 RE EAT PR G
R CK
RE O E ‚⁄ 1 2 3 4
SE S R SC M N S C 5 6 7 8
¤ ‚‹ fi‚
9 1 11 2
31 15 6
5 D ATIC DISC LOADING SYSTEM
ENGLISH
P USE PL Y
PE O E D C SK P
9