Chapter 2. Transport And Installation - gala gar D-12 A Manuel Technique D'instructions

Standard equipment supplied with:
D-12 A: Drive rollers
-
D-20 A: Drive rollers
-
D-20 AR: Drive rollers
-

CHAPTER 2. TRANSPORT AND INSTALLATION.

Knocks and sudden movements must be avoided when transporting the equipment. The transport position
will be shown by arrows on the packaging. In any case, the packaging must be protected from water.
2.1. ELECTRICAL SUPPLY INSTALLATION.
The electrical installation of the equipment making up the system must be carried out by specialised
personnel according to the standards in force.
The location must meet the following requirements:
Place: Dry and ventilated, far enough away from the welding area in order to prevent the metal dust
caused by the welding process from getting into the equipment. The equipment must not be used in the rain.
PLACE THE WELDING MACHINE ON A FIRM FLAT SURFACE.
IF EQUIPMENT OF THIS KIND TIPS OVER IT CAN HAVE VERY SERIOUS CONSEQUENCES.
The electrical connection of the wire-feed unit is carried out with an extension, which connects it to the
GALA INDUSTRIAL power source. The different recommended possibilities are defined in table 2.
EXTENSION CORDS
RECOMMENDED WELDING TORCH
The general installation process is described in the GALA INDUSTRIAL power source manual. Read this
section carefully.
GALA GAR guarantees correct operation against all manufacturing defects of the GALA INDUSTRIAL D-12 A, D-20 A y D-20 AR
products, as from the purchase date (guarantee period) of:
•
12 MONTHS
This guarantee will not be applied to components with a working life that is less than the guarantee period, such as spares and
consumables in general.
In addition, the guarantee does not include the installation, start-up, cleaning or replacement of filters, fuses and cooling or oil
refills.
If the product should present any defect during the guarantee period, GALA GAR undertakes to repair it without any additional
charge, unless the damage caused to the product is the result of accidents, improper use, negligence, inappropriate accessories,
unauthorized servicing or modifications to product not carried out by GALA GAR.
The decision to repair or replace parts or supply a new appliance will depend on the criterion of GALA GAR. All replaced parts
and products will be the property of GALA GAR.
In order for the guarantee to become effective the product and the purchase invoice must be handed over, duly completed and
stamped by an authorized Technical Service. Shipping and transport expenses will be on the user's account.
Damage or unforeseen or indirect expenses resulting from an incorrect use will not be the responsibility of GALA GAR.
D-12 A, D-20 A, D-20 AR. Instructions Manual.
40mm 0.8/1.0 – 1.0/1.2. Instructions manual.
φ
30mm 1.0/1.2. Instructions manual.
φ
30mm 1.0/1.2. Cooling connectors. Instructions manual.
φ
TABLE 2. Recommended Extension Cords and Welding Torch.
Cable 35 mm
Cable 35 mm
Cable 50 mm
GM 36 Ref. 006308
GENERAL GUARANTEE CONDITIONS
WIRE-FEED UNITS
Ref. 618.00.000
D-12 A
2 (5 mt) Cable 50 mm
Ref. 637.00.000
2 (10 mt) Cable 50 mm
Ref. 637.81.000
2 (20 mt) Cable 70 mm
Ref. 637.82.000
GM 36 Ref. 006308
Ref. 621.00.000
D-20 A D-20 AR (Cooled)
2 (5 mt) Cable 70 mm
Ref. 638.00.000
2 (10 mt) Cable 70 mm
Ref. 638.81.000
2 (20 mt) Cable 70 mm
Ref. 638.82.000
MB-501-D Ref. 005824
11
Ref. 622.00.000
2 (5 mt)
Ref. 639.00.000
2 (10 mt)
Ref. 639.81.000
2 (20 mt)
Ref. 639.82.000