SSS Siedle MOCT 711-0 Mode D'emploi page 9

(320 horizontal x 3 x 240 vertical)
• Input signal BAS-1 Vss to 75 Ω
• Supply voltage 20 to 30 V DC
• Operating current max. 400 mA
• Bias current appr. 150 mA
• Ambient temperature 0-30 °C
Commissioning
Following correct installation, the
MOCT 711-... is immediately ready
for use as a monitor. The time and
date must be set for the video
memory. However, for touchscreen
function, no custom-specific pro-
gramming is required.
Operation
Setting the date and time using
the buttons:
Hold down the "Play" and "Reset"
buttons simultaneously for 3 secs.
The status is indicated on the
display.
The "Play" button is used to select
and simultaneously highlight the
hour, minute, month, day and year
indication.
The "Reset" button is used to incre-
ase the value indicated in the selec-
ted flashing input field.
The "Reset" button can be either
pressed repeatedly or held down.
Terminating the setting mode
To terminate the setting mode, press
the „Play" button repeatedly until
there is no longer a field flashing.
Switch off the MOCT with the
„Reset" button.
Setting the date and time via the
touchscreen
Alternatively, the clock can also be
set using the touchscreen user inter-
face. The relevant information is
provided in the documentation on
the enclosed CD.
Display and storage of the cur-
rent camera image
In the case of a door call, the cur-
rent camera image is displayed.
Using the arrow keys, the camera
CMM/CMC 511/611-... can be hori-
zontally and vertically controlled.
The camera image is automatically
stored 5 seconds after the door call.
The time required for storing
depends upon the size (data quanti-
ty and quality) of the image being
stored.
Start of storage (5 secs.) can be
changed in the configuration menu.
For the relevant information, see the
documentation on the provided CD.
It is not possible to manually
store the camera image.
If the call button is actuated again
before around 30 seconds have
expired, no repeat storage process
takes place. If the storage capacity is
exhausted, the oldest stored image
is deleted to allow the latest picture
to be stored.
The MOCT switches off around
15 secconds after the end of a call.
If the door call is not accepted, the
system switches off after 45 secs.
The MOCT can be switched off
immediately using the „Reset"
button.
Displaying and deleting stored
images:
By actuating the "Play" button, al-
ready stored images are displayed
on the monitor, starting with the
most recent.
The image number and the time
and date stored are superimposed
on the stored images.
Index through the images with the
"Play" button.
Deleting
Scroll through all the images until
you reach the most recent one.
After this the star * and the current
date and time will appear.
By actuating the "Reset" button for
> 2 secs, all stored images are dele-
ted.
It is not possible to delete indivi-
dual stored images.
Actuating the "Reset" button < 2
secs. switches the monitor off
immediately.
Switching off the monitor
The MOCT can be switched off at
any time by briefly pressing the
„Reset" button.
Programming
The programming software on CD
and the adapter cable are enclosed.
Insert the supplied CD with the pro-
gramming software into the CD
drive and start the installation by
double clicking on Setup.exe
Programming takes place in dialo-
gue between the programmer and
laptop.
For our technical hotline and advice
relating to the MOCT 711-...
Tel. +49 (0)7723 / 63-420
PC system requirements for
installing the configuration pro-
gram
Laptop computer: Minimum require-
ment Pentium processor with CD-
ROM drive and serial interface
Working memory: at least 32 MB
User interface:
Windows 95, 98, ME, NT 4.0, 2000
or XP
Graphics card:
min. 800x600 Pixel 65 000 colours
Printer with Windows drive
One free serial interface.
Operaton
The user interface is switched on
by contact with the touchscreen,
making the operating elements
visible.
Note!
Observe the remarks and operating
mode of the used circuit diagrams in
the Planning and Installation
Guidelines.
5