Installation Instructions; Operation - Scheppach TIGER 2000S Traduction Des Instructions D'origine

m Warning!
Always ensure that the machine is switched off and disconnect-
ed from the power supply before changing the device settings.
• All covers and safety devices must be properly fitted before
switching on the device.
• The grindstone must be able to run freely.
• Before operating the on/off switch, make sure that the grind-
stone and honing wheel are correctly mounted and that the
moving parts of the device function smoothly. Visually inspect
both for defects.
• Replace a damaged or worn grindstone.

9. Installation instructions

9.1 Installation and setting
Please make sure that your grinding machine stands upright
and stable on a solid surface with sufficient lighting.
The machine has no front or rear side. Grinding can take place
either with or against the direction of rotation.
Tools required for all assembly / adjustment steps:
• Open-ended spanner 19 mm (not included in the scope of
delivery)
The grindstone is not pre-assembled for packaging reasons
m Warning!
Do not connect the device to the power supply until assembly is
complete. Failure to do so may result in accidental starting and
possibly serious injury.
9.2 Sound test
Check the grindstone for cracks and perform a sound test for
crack detection.
• The grindstone must be removed from the machine for the
sound test. The grindstone stands upright on the floor. On a
hard floor, use a piece of wood as a support. The grindstone
must be dry.
• Lightly tap the grinding disc with a non-metallic hammer. A
crack-free disc has a high, purely bell-like sound. A disc that
has a crack produces a muffled sound. If the grindstone is
flawless, it can be fitted.
9.3 Installing the grindstone (Fig. 2+3)
Only use grindstones with identical technical data (see 10.
Technical data).
• Remove the nut (11) with an open-ended spanner, the outer
washer (9) and the cardboard transport sleeve of the grind-
ing shaft (10). To do so, firmly hold the star grip for the leath-
er honing wheel (14). Attention: Left-handed thread.
• The water tank (8) must be removed. (see 9.4)
• Place the grindstone on the grinding shaft (10). The inner
washer must be behind the grindstone.
• Fit the grindstone (12) as shown in Fig. 2.
• Fasten the grindstone with the washer (9) and the nut (11)
using an open-ended spanner. To do so, firmly hold the star
grip of the leather honing wheel (14). Attention: Left-handed
thread.
9.4 Fitting the workpiece support (1) (Fig.4 + 5)
The workpiece support (1) can be attached both to the up-
per mount for workpiece support (2) and to the side mount for
workpiece support (15). This depends on whether you wish to
work with or against the grinding direction.
9.4.1 Fitting the upper mount
• To attach the workpiece support (1) to the upper mount for
workpiece support (2), first attach the two loose star grip screws
(3). Screw them into the upper workpiece support (2) (threaded
hole) at the intended position with approx. 2-3 turns.
• Then insert the workpiece support into the holes of the upper
mount for workpiece support (2).
• Fasten this at the desired height with the two star grip screws
(3).
9.4.2 Fitting the side mount
• The two star grip screws (3) for the side mount for workpiece
support (15) are pre-assembled.
• To mount the workpiece support (1) here, insert the work-
piece support into the holes in the side mount for workpiece
support (15).
• The workpiece support (1) is now fixed for the first step.
9.5 Installing the water tank (Fig. 6 + 7)
• Attach the water tank (8) in the lowest position to the brack-
ets for the water tank (16) (behind the grindstone) on the
machine housing (5). (Fig. 6)
• Then fill the tank with water up to the recess. (Fig. 7)

10. Operation

ATTENTION!
Remove the mains plug before any maintenance, modification
and assembly work.
10.1 Grinding direction (Fig. 4 + 5)
This primarily depends on whether you wish to work with or
against the grinding direction.
If you wish to remove large quantities of steel quickly (e.g. from
very old, rusty tools) or if you want to grind coarse tools such
as axes, it is advisable to work against the grinding direction.
If you wish to grind more accurately, we recommend working
with the grinding direction. This applies, for example, when
grinding tools and blades.
Please note that the grinding process is slowed down when you
work with the direction of rotation. Please check before each
operation that the surface of the grindstone is flat. To do this,
lower the workpiece support onto the stone and turn it manu-
ally through 360°. If necessary, break off uneven material with
a stone cutter.
GB/IE 17