Warranty; Troubleshooting Guide - DeWalt DW717 (120 Volt) Guide D'utilisation

use identical replacement parts.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty
E
materials or workmanship for three years from the date of
purchase. This warranty does not cover part failure due to
normal wear or tool abuse. For further detail of warranty
coverage and warranty repair information, visit www.
dewalt.com or call 1-800-4-D WALT (1-800-433-9258).
E
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states or
provinces.
In addition to the warranty, D WALT tools are covered by
E
our:
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts
E
caused by normal use, for free, any time during the first
year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason,
E
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained either
in the packaging, call the local company or see website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your
warning labels become illegible or are missing, call
1-800-4-D WALT for a free replacement.
E
Patent Notification
Manufactured under one or more of the following U.S.
patents:
6,823,765 6,101,914 5,907,987
6,810,780 6,035,754 5,862,734
6,520,059, 6,032,563 5,582,089
Other patents may be pending.
TROUBLE!
SAW WILL NOT START
SAW MAKES
UNSATISFACTORY CUTS
BLADE DOES NOT COME UP
TO SPEED
MACHINE VIBRATES
EXCESSIVELY
DOES NOT MAKE ACCURATE
MITER CUTS
MATERIAL PINCHES BLADE
5,375,495
5,285,708
5,199,343

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
WHAT'S WRONG?
1. Saw not plugged in
2. Fuse blown or circuit breaker
tripped
3. Cord damaged
4. Brushes worn out
1. Dull blade
2. Blade mounted backwards
3. Gum or pitch on blade
4. Incorrect blade for work being done
1. Extension cord too light or too long
2. Low house current
1. Saw not mounted securely to stand
or work bench
2. Stand or bench on uneven floor
3. Damaged saw blade
1. Miter scale not adjusted correctly
2. Blade is not square to fence
3. Blade is not perpendicular to table
4. Workpiece moving
1. Cutting bowed material
15 15
WHAT TO DO
1. Plug in saw
2. Replace fuse or reset circuit breaker
3. Have cord replaced by authorized ser-
vice center
4. Have brushes replaced by authorized
service center or replace them yourself
as instructed on Page 9.
1. Replace blade, see Page 6.
2. Turn blade around, see Page 6.
3. Remove blade and clean with turpen-
tine and coarse steel wool or house-
hold oven cleaner
4. Change the blade type, see pages 6.
1. Replace with adequate size cord, see
Page 2.
2. Contact your electric company
1. Tighten all mounting hardware, see
Page 6.
2. Reposition on flat level surface, see
Page 6.
3. Replace blade, see Page 6.
1. Check and adjust, see Page 7.
2. Check and adjust, see Page 8.
3. Check and adjust fence, see Page 8.
4. Clamp workpiece securely to fence or
glue 120 grit sandpaper to fence with
rubber cement.
1. Position bowed material as shown on
Page 13.