Maintenance; Warranty - DeWalt DW715 Guide D'utilisation

surface finish, may require the use of a clamp or fixture to
prevent movement during the cut. Position the material so
that you will be cutting the thinnest cross section, as shown
in Figure 19. Figure 19A illustrates the wrong way to cut
these extrusions. Use a stick wax cutting lubricant when
cutting aluminum. Apply the stick wax directly to the saw
blade before cutting. Never apply stick wax to a moving
blade.
The wax, available at most hardware stores and industrial
mill supply houses, provides proper lubrication and keeps
chips from adhering to the blade.
Be sure to properly secure workpiece. Refer to page 4 for
correct saw blade.
BOWED MATERIAL
When cutting bowed material always position it as shown
in Figure 20 and never like that shown in Figure 20A.
Positioning the material incorrectly will cause it to pinch the
blade near the completion of the cut.
CUTTING PLASTIC PIPE OR OTHER ROUND
MATERIAL
Plastic pipe can be easily cut with your saw. It should be
cut just like wood and CLAMPED OR HELD FIRMLY TO
THE FENCE TO KEEP IT FROM ROLLING. This is
extremely important when making angle cuts.
CUTTING LARGE MATERIAL
Occasionally you will encounter a piece of wood a little too
large to fit beneath the blade guard. If this occurs, simply
place your right thumb on the upper side of the guard and
roll the guard up just enough to clear the workpiece, as
shown in Figure 16. Avoid doing this as much as possible,
but if need be, the saw will operate properly and make the
bigger cut. NEVER TIE, TAPE, OR OTHERWISE HOLD
THE GUARD OPEN WHEN OPERATING THIS SAW.

Maintenance

1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even
though slots are provided to allow debris to pass
through, some dust will accumulate.
3. The brushes are designed to give you several years
of use. If they ever need replacement follow the
instructions on page 7 or return the tool to the nearest
service center for repair. Service center locations are
packed with your tool.
Repairs
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (including brush inspection
and replacement) should be performed by authorized
service centers or other qualified service organizations,
always using identical replacement parts.
FIG. 20
RIGHT
FIG. 20A
WRONG
13
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
E
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
E
9258). This warranty does not apply to accessories or
damage caused where repairs have been made or
attempted by others. This warranty gives you specific legal
rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, D WALT tools are covered by
E
our:
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts
E
caused by normal use, for free, any time during the first
year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason,
E
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
RECONDITIONED PRODUCT: Reconditioned product is
covered under the 1 Year Free Service Warranty. The 90
Day Money Back Guarantee and the Three Year Limited
Warranty do not apply to reconditioned product.
FREE WARNING LABEL REPLACEMENT: If your
warning labels become illegible or are missing, call
1-800-4-D WALT for a free replacement.
E
Patent Notification
Manufactured under one or more of the following U.S.
patents:
6,431,040 5,375,495
6,427,570 5,285,708
5,819,619 5,199,343
D346,173
Other patents pending.
WALT (1-800-433-