Maintenance; Repairs; Warranty - DeWalt DW713 Guide D'utilisation

FIG. 31
The wax, available at most hardware stores and industrial
mill supply houses, provides proper lubrication and keeps
chips from adhering to the blade.
Be sure to properly secure workpiece. Refer to Saw Blades
under Accessories for correct saw blade.
BOWED MATERIAL
When cutting bowed material always position it as shown in
Figure 31 and never like that shown in Figure 32. Positioning
the material incorrectly will cause it to pinch the blade near
the completion of the cut.
CUTTING PLASTIC PIPE OR OTHER ROUND
MATERIAL
Plastic pipe can be easily cut with your saw. It should be cut
just like wood and CLAMPED OR HELD FIRMLY TO THE
FENCE TO KEEP IT FROM ROLLING. This is extremely
important when making angle cuts.
CUTTING LARGE MATERIAL
Occasionally you will encounter a piece of wood a little too
large to fit beneath the blade guard. A little extra height can
be gained by rolling the guard up out of the way, as shown in
Figure 24. Avoid doing this as much as possible, but if need
be, the saw will operate properly and make the bigger cut.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.

MAINTENANCE

DO NOT use lubricants or cleaners (particularly spray or
aerosol) in the vicinity of the plastic guard. The polycarbonate
material used in the guard is subject to attack by certain
chemicals.
1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
FENCE
CORRECT
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even though
slots are provided to allow debris to pass through, some
dust will accumulate.
3. The brushes are designed to give you several years of
use. To replace the brushes refer to Brushes on page 8
or return the tool to the nearest service center for repair.
A list of service center locations is packed with your tool.
Service Information
Please have the following information available for all service
calls:
Model Number _____________________________ Type ___
Serial Number ______________________________________
Date and Place of Purchase __________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by a
D WALT factory service center, a D
E
center or other qualified service personnel. Always use
identical replacement parts.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty
E
materials or workmanship for three years from the date of
purchase. This warranty does not cover part failure due to
normal wear or tool abuse. For further detail of warranty
coverage and warranty repair information, visit www.dewalt.
com or call 1-800-4-D
warranty does not apply to accessories or damage caused
where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
FIG. 32
INCORRECT
In addition to the warranty, D
D WALT will maintain the tool and replace worn parts
E
caused by normal use, for free, any time during the first year
after purchase.
If you are not completely satisfied with the performance of
your D
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
WALT authorized service
E
Please refer to the beginning of the manual for labels.
WALT (1-800-433-9258). This
E
14
WALT tools are covered by our:
E
1 YEAR FREE SERVICE
90 DAY MONEY BACK GUARANTEE
WALT Power Tool, Laser, or Nailer for any reason,
E
WALT
E