Safety; General Safety Regulations; A For Machines With Electric Motor (Sps 42 T) - Bell STS 42 Livret D'emploi Et D'entretien

ENGLISH

3 - SAFETY

The information given in the chapter is extremely important for safety purposes. It describes possible hazards tied to use of the
machine and instructions for correct use of this to avoid injury or damage.
WARNING: The log splitter BELL mod. SPS 42 and mod. STS 42 have been designed and manufactured to split logs of the sizes recommended in
fig.2, p.2 only.
Use of the machine for any other purpose shall be considered improper and the manufacturer shall not be liable for any injuries
or damage to be ascribed to improper use of the machine.
The operator must only work in the position shown in fig.1, pos.15, and only operate the machine drive control with both hands without using other
makeshift systems or tampering with the controls.
When the machine is being used, persons other than the operator and animals must be keep at a distance of at least 5 meters from the machine.
NEVER ATTEMPT TO TAMPER WITH THE PROTECTIONS OF THE LOG SPLITTER OR TO OPERATE THE MACHINE WITHOUT THESE.
FAILURE TO COMPLY WITH THE INSTRUCTIONS GIVEN IN THIS CHAPTER MAY RESULT IN SERIOUS INJURY OR DAMAGE TO PERSONS,
THINGS AND TO THE MACHINE.
Do not use the log splitter to break stone materials (stones, concrete, etc.). Or to crush pieces or metal containers.

3.1 - General safety regulations

•
The machine must always be used by one operator only.
•
Do not use the machine outdoor when it is raining or snowing.
•
Nobody must be allowed to use the log splitter unless they have read the instruction manual and have been instructed in the regulations to
follow for correct and safe use.
•
Use of the log splitter by apprentices of not less than 16 years of age must be supervised by an adult authorised to use the machine.
•
Never wear loose, unbuttoned clothing which may become trapped in moving parts.
•
Do not move the log splitter while the motor is running.
•
Use a piece of cardboard or wood rather than the hands in order to search for eventual oil leakages.
Oil jets under pressure can penetrate under skin. In this case, see a doctor at once.
•
Do not work on sloping or slippery ground. position the machine in a flat area free from objects which may impede the freedom of movement
of the operator.
•
Check that the logs to be split are free from nails or wire, which may fly up or damage the machine. the ends of the logs must be cut square.
branches must be cut off flush with the trunk.
•
Never try to split logs larger than those indicated in fig.2, page 2. This could be dangerous and may damage the machine.
•
Break wood in the direction of the grain. do not place wood across the log splitter and leave it in that position for splitting; it may be dangerous
and may seriously damage the machine.
•
Never attempt to cut two logs at once; one may fly up and hit you.
•
If the log moves away from the blade, retract the ram or the blade and turn the log through 90°.
•
Do not attempt to load the log in the log splitter while the ram is in motion. you could get trapped and injured.
•
Keep your hands well away from any splits and cracks which open in the log; these may close suddenly and crush or amputate your fingers.
•
Do not force the log splitter for more than 30 seconds by keeping the cylinder under pressure at the end of its stroke, or by persisting when
a log does not split or gets stuck on the blade. Oil under pressure overheats very rapidly, damaging the pump.
•
Never leave the machine unattended while it is running. If you leave the machine, even for a short time, remove the power supply or any
possible cause of accidental start-up.
•
The log splitter must never be used by an operator who is under the influence of alcohol, drugs, medicines, or who is tired. A clear mind is
essential for safety.
•
Never try to release a jammed log while the machine is running. The machine must be switched off during this operation.
•
Never request the assistance of another person to help you remove a jammed log.
•
Do not use alcohol, petrol, or solvents to clean the machine. This could cause the safety information applied to the machine itself to become illegible.
3.1.A - For machines with electric motor (SPS 42 T)
•
Do not use machines with electric motor if natural gas, petrol fumes or other inflammable vapours are present.
•
Check that the electric circuit to which the machine will be connected is suitable.
be checked (verify the nameplate on the motor and the data in this manual). The machine must be connected to a circuit with a regulation
differential switch upstream and, in compliance with the norms (30 mA rated fault current), with a ground connection.
•
Use cables with a section of 2.5 mm
material suitable for outdoor use.
section may cause voltage drops and don't allow the motor to develop all the power.
damage before using it.
•
Make sure that the machine and the cable never come in contact with water.
•
To prevent accidental start-up, ensure that the switch is "off" before plugging in the power cable.
•
Treat the power cable with care. do not attempt to move the machine by pulling the cable. do not yank the cable to unplug it; keep the cable away
from excessive heat, oil and sharp objects.
•
Never leave the machine unattended with the power supply "on". also disconnect the power cable when not in use, when carrying out
maintenance work, when changing attachment or moving the machine.
D22000135 - v.0 - UPD 290110
. Avoid use of free and inadequately insulated connections. Connections must be made with protected
2
Do not use cable extensions longer than 5 mt.: too long cables or cables with inadequate
Power, voltage and frequency of the motor must
Always check the cable extension for any
21