IMG STAGELINE TXS-865HT Mode D'emploi page 10

6) The transmitter is provided with a lock function
GB
to prevent accidental change of settings or
switching off
7) To switch off the transmitter, keep the button
/ (2) pressed until the display shows
Then the transmitter is switched off.
5.1 Setting the transmitter
When the transmitter is not locked, press the button
SET (4) to activate the setting modes one after
another:
group (keep button pressed for a while) → channel
→ sensitivity → transmission power → automatic
frequency matching → identification number → lock
function
To make settings in a setting mode, see the corre-
sponding chapter 5.1.1 to 5.1.6.
To exit a setting mode without changing a setting,
press the button SET repeatedly until the display
briefly shows
normal mode.
5.1.1 Transmission frequency (group / channel)
To set the transmitter quickly and easily to the
transmission frequency of the receiver unit, use the
REMOSET function (
ever, it is also possible to set the transmission fre-
quency of the transmitter manually by selecting the
channel group and the channel. The table on page
20 gives an overview of the groups and channels.
1) Keep the button SET (4) pressed until the dis-
play briefly shows
tion (
...
mode is activated.
2) Select the group with the button
ton (5).
3) Press the button SET to confirm. The channel
indication starts flashing on the display; the
channel setting mode is activated.
4) Select the channel with the button
ton .
5) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.2 Sensitivity
For the microphone sensitivity, several levels are
available: from 12 dB (maximum sensitivity) to
-18 dB (minimum sensitivity).
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
10
chapter 5.1.6.
. The unit will then return to the
chapter 5, step 3). How-
. Then the group indica-
starts flashing; the group setting
)
(3) or the but-
. The unit will then return to
and then the group set-
2) Press the button SET repeatedly until the dis-
play briefly shows
sensitivity.
3) Press the arrow buttons to set the sensitivity in
such a way that you obtain an optimum volume
.
level of the microphone. If the volume is too
high, the microphone will distort; in this case, set
a lower value with the button
is too low, there will be a poor signal-to-noise
ratio; in this case, set a higher value with the
button
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.3 Transmission power
For the transmission power, two values are avail-
able. With a high transmission power, the range will
increase; however, the operating time of the batter-
ies will decrease due to faster discharge.
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
2) Press the button SET repeatedly until the dis-
play shows the current transmission power:
3) Press the button
or press the button
4) Press the button SET to confirm. The display
briefly shows
the normal mode.
5.1.4 Automatic frequency matching
(REMOSET function)
To enable / disable the automatic frequency match-
ing (REMOSET function = frequency setting of the
transmitter via a radio signal of the receiver unit) for
the transmitter:
or the but-
1) Keep the button SET (4) pressed until the dis-
play briefly shows
ting mode (group indication starts flashing).
2) Press the button SET repeatedly until the dis-
play shows the current setting for the automatic
frequency matching:
3) Press the button
setting
and then the current
(5).
. The unit will then return to
and then the group set-
low transmission power (10 mW)
high transmission power (50 mW)
(3) to select the setting
(5) to select the setting
.
. The unit will then return to
and then the group set-
automatic frequency matching enabled
(i. e. frequency setting of the transmitter
via the REMOSET function is possible)
automatic frequency matching disabled
(i. e. no REMOSET transmission)
(3) to select the setting
or press the button
.
(3). If the volume
(5) to select the