Sporty Mode; Cleaning And Maintenance - Tunturi E50R Manuel De L'utilisateur

- Use Dial UP/ DOWN key to select ADVANCE
program 1~4 ( fig. F-13) and press MODE/ ENTER
to confirm.
- Use Dial UP/ DOWN key to set time, press MODE/
ENTER to confirm.
- Press START/ STOP key to start workout
- Use Dial UP/ DOWN key to adjust resistance level.
- Load level is shown in LOAD window for a few
seconds, than changes back into Watt load again.

Sporty mode

- Use Dial UP/ DOWN key to select workout
program, choose SPORTY mode and press mode
key to enter next setting entry for SPORTY mode
program.
- Use Dial UP/ DOWN key to select SPORTY program
1~4 ( fig. F-14) and press MODE/ ENTER to
confirm.
- Use Dial UP/ DOWN key to set time, press MODE/
ENTER to confirm.
- Press START/ STOP key to start workout
- Use Dial UP/ DOWN key to adjust resistance level.
- Load level is shown in LOAD window for a few
seconds, than changes back into Watt load again.
Cardio mode.
- Use Dial UP/ DOWN key to select workout
program, choose CARDIO mode and press mode
key to enter next setting entry for CARDIO mode
program.
- Use Dial UP/ DOWN key to set age ( fig. F-15)
- Use Dial UP/ DOWN key to select 55% ( fig. - 16),
75%, 90% or TAG (Target H.R. _ Default 100)
- Use Dial UP/ DOWN key to set time, press MODE/
ENTER to confirm.
- Press START/ STOP key to start workout
- Use RESET, to go back to main menu.
Recovery
- The RECOVERY key will only be valid if pulse is
detected.
- TIME will show „0:60" (seconds) and counts down
to 0. (fig. F-19)
- Computer will show F1 to F6 (fig. F20) after the
countdown to test heart rate recovery status. User
can find the heart rate recovery level based on the
chart below.
- Press RECOVERY key again to return to the
beginning.
F1 Outstanding
F2 Excellent
F3 Good
F4 Fair
F5 Below average
F6 Poor
NOTE
• When entering "RECOVERY" mode, the workout
will be paused.
• Press START/ STOP to resume training when exit
"RECOVERY" mode, or press "RESET" to go
back to start menu.
Body Fat
- Press the BODY FAT key to start body fat
measurement. (fig. F-22)
- During measuring, users have to hold both hands
on the hand grips. LCD display "-" "- -" "- - -" "- - -
-" (fig. F-25) for 8 seconds until computer finish
measuring.
- LCD will display BMI and FAT % (fig. F23/ F-24).
NOTE
• Correct "User Profile Settings" is required for this
function.
Body fat mode error codes
- *E-1
There is no heart rate signal input detected.
- *E-4 (fig. F-25)
Occurs when FAT% and BMI result is below 5 or
exceeds 50.
Trouble shooting:
- When the display of LCD is dim, it means the
batteries need to be changed.
- If there is no signal when you pedal, please check if
the cable is well connected.
NOTE
• When stop training for 4 minutes, the main
screen will be off.
• If the computer displays abnormally, please re-
install the transformer and try again.

Cleaning and maintenance

The equipment does not require special maintenance.
The equipment does not require recalibration when
it is assembled, used and serviced according to the
instructions.
WARNING
• Do not use solvents to clean the equipment.
• Clean the equipment with a soft, absorbent cloth
after each use.
• Regularly check that all screws and nuts
are tight.
• If necessary, lubricate the joints.
2 3
English