Automatic Restart; General Instructions; Preventive Maintenance - Parker Hyperchill Plus ICEP007 Manuel D'utilisation

4.9 Alarm/Warning history
set
ALHi
esc
set
HySP
esc set
0 1 2
esc
set
HySP
HySt
HySd
HySC
esc set set
set
esc
esc
18.06 13.46
04
Menu Code DESCRIPTION
HySP Alarm number
HySC See alarm code
See day and month of the alarm
HySd
(if the clock option is present)
ALHi See hour and minutes of the alarm
HySt
(if the clock option is present)
HyS1 b1 temperature at time of the alarm
HyS2 b2 temperature at time of the alarm
HyS3 SET conditions at time of the alarm
set
Press the button " " to enter in the menu, using the buttons "
" select the parameter " ALHi".
"and "
set
Press the button " " to enter in the menu, using the buttons "
"and " " select the parameter "HySP".
set
Press the button " " to enter in the menu, using the buttons "
"and " " select the alarm number insert (0,1,2......39) and confi rm
set
with " " (the number 0 is the last alarm started) .
set
"HySP" appears again, press " " to enter and see the date of the
English
alarm: "HySC" code (es:HP), "HySd" Date (day, month), "HySt" hour
(hour, minutes), "HyS1" "HyS2" "HyS3" sensor b1, b2 and set when the
alarm occurred.
esc
Press " " to exit.

4.10 Automatic restart

In the event of a power failure, when power is restored the chiller will
assume the On-Off status held at the moment the power was lost.
5 Maintenance
a) The machine is designed and built to guarantee continuous opera-
tion; however, the life of its components depends on the maintenan-
ce performed.
b) Z When requesting assistance or spare parts, identify the machine
(model and serial number) by reading the data plate located on the
unit.
c) Circuits containing 5t < xx < 50t of CO2 are checked to identify
leaks at least once a year.
Circuits containing 50t < xx < 500t di CO2 are checked to identify
leaks at least once every six months. ((EU) No. 517/2014 art. 4.3.a,
4.3.b).
HyS1
d) For machines containing 5t CO2 ore more, the operator must keep a
record stating the quantity and type of refrigerant used, an quantities
set
esc
added and that recovered during maintenance operations, repairs
and fi nal disposal ((EU) No. 517/2014 art. 6). .An example of this
record sheet can be downloaded from the site: www.polewr.com.
28

5.1 General instructions

!
Before performing any maintenance, make sure the power to the
refrigerator is disconnected.
Y
Always use the Manufacturer's original spare parts: otherwise the
Manufacturer is relieved of all liability regarding machine malfunctio-
ning.
Y
In case of refrigerant leakage, contact qualifi ed and authorized
personnel.
Y
The Schrader valve must only be used in case of machine malfun-
ction: otherwise any damage caused by incorrect refrigerant charging
will not be covered by the warranty.

5.2 Preventive maintenance

To guarantee lasting maximum chiller effi ciency and reliability, carry out:
Z
a) every month - clean the condenser fi ns (for biogas version);
Z
b) every 6 months - clean the condenser fi ns and make sure
compressor electrical absorption is within the dataplate values;
ICEP007-030
Z
c) kit for maintenance.(par.7.5)
• kit for maintenance;
• service kit;
• individual spare parts.
5.3 Refrigerant
Z
Charging: any damage caused by incorrect charging carried out
by unauthorized personnel will not be covered by the warranty.
Y
The equipment contains fl uorinated greenhouse gases.
At normal temperature and pressure, the R407C refrigerant is a co-
lourless gas classifi ed in SAFETY GROUP A1 - EN378 (group 2 fl uid
according to Directive PED 2014/68/EU);
GWP (Global Warming Potential) = 1774.
!
In case of refrigerant leakage, air the room.
5.4 Dismantling
The refrigerant and the lubricating oil contained in the circuit must be
recovered in conformity with current local environmental regulations.
The refrigerant fl uid is recovered before fi nal scrapping of the
equipment ((EU) No. 517/2014 art.8).
%
frame and panels steel/epoxy resin polyester
tank aluminium/copper/steel
pipes/collectors copper/aluminium/carbon steel
pipe insulation NBR rubber
compressor steel/copper/aluminium/oil
condensator steel/copper/aluminium
pump steel/cast iron/brass
fan aluminium
refrigerant R407C (HFC)
valve brass/copper
electrical cable copper/PVC
Equipment containing electrical components
must be disposed separately collected with
electrical and electronic waste according to
local and currently legislation.
Recycling
Disposal
7 / 8