Receiving Intercom Calls; Initiate Intercom Calls - SCHUBERTH SRC-System Guide D'utilisation

Use Channel "A"
First SRC-System™
Rider "A"
In this configuration Rider "B" is paired to Rider "A" and to Rider "C".
IMPORTANT: Since Rider "B" uses two Bluetooth® connections during the
conference mode, Rider "B" will be disconnected from the mobile phone or GPS
device until the conference mode is terminated. Upon termination, Rider "B" will
automatically re-connect to his mobile phone or GPS. Rider "A" and "C" remain
connected to their mobile phones or GPS devices during the 3-way intercom call.
Set‑up and configuration of three‑way intercom connectivity
INteRCOm PAIRING / CONNeC‑
CHANNeL tION BUttON
CHANNEL "A" CHANNEL "A" BUTTON
CHANNEL "B" CHANNEL "B" BUTTON
PAIRING OPtIONS BetWeeN tHRee PARtICIPANtS
Pairing three SRC‑System™ headsets is achieved by simply repeating
the procedure in the above section 9.4a with a third SRC‑System™
headset (in a different CHANNEL).
1. Pair your SRC‑System™ with the second SRC‑System™ as
described in section 9.4a (Using CHANNEL "A").
2. Pair your SRC‑System™ with the third SRC‑System™ as
described in section 9.4a (Using CHANNEL "B")
34
QG SRC 207 - MAN00015.indd 34
Use Channel "B"
Third SRC-System™
Rider "C"
Second SRC-System™
Rider "B"
PAIRING mODe LeD
INDICAtORS
Rapid RED flashing
Rapid BLUE flashing

Initiate Intercom calls

There are two ways to start an Intercom call with your paired headsets
while the headset is in Standby mode:
VOICe CONNeCt: CHANNeL BUttON CONNeCt:
Start talking loudly Single tap the CHANNeL "A" Button
Once you start talking loudly, an to add or remove the CHANNEL "A"
Intercom call will be established headset from an Intercom call.
with both paired headsets, Single tap the CHANNeL "B" Button
CHANNEL "A" and CHANNEL "B" to add or remove the CHANNEL "B"
(if both are available). headset from an intercom call.

9.5 RECEIVING INTERCOM CALLS

Once another paired headset tries calling you via intercom, the call
will begin almost instantly.
NOTe: The headsets preset priority modes have been set in a way to avoid in-
coming intercom calls from interrupting mobile phone calls and GPS instruc-
tions in progress. In such case the intercom caller will hear a busy signal and
you will hear two beeps, indicating that an intercom caller is trying to page
you. (see section 4.3 for details on audio priorities of paired devices).
9.6 INITIATE INTERCOM CALLS
There are two ways to start an Intercom call with headsets that are paired to
your SRC‑System™ (make sure you are in Standby mode):
VOICe CONNeCt:
Preferred for relatively brief conversations
as it takes the channel into standby mode
after 30 seconds of silence
Start talking loudly
Once you start talking loudly, an
Intercom call will be established with
both paired headsets, CHANNEL "A" and
CHANNEL "B" (if both are available).
The Intercom call will stay on until all
participants remain silent for 30 seconds.
(Applicable for 2-way communication)
CHANNeL BUttON
CONNeCt:
Preferred for extended conversa-
tions as it leaves the channel
open and active
Single tap the CHANNEL "A"
Button to add or remove the
CHANNEL "A" headset from an
Intercom call.
Single tap the CHANNEL "B"
Button to add or remove the
CHANNEL "B" headset from an
intercom call.
2/1/11 11:38 AM