Table des Matières
Publicité
PIECES AILES
(A) Aile (avec aileron et volet montés sur charnières et à coller) ................. (G/D)
............................................................................................................. 1 de chaque
(B) Tringlerie ailerons (acier Ø2x65mm) ..............................................................2
(C) Tringlerie volets (acier Ø2x50mm) ..................................................................2
(D) Chape rotule avec visserie(vis M2x10+écrou+rondelle) ...................... 8 sets
(E) Guignol ailerons et volets ................................................................................ 4
(F) Vis fixation d'aile (plastique M4x25mm) .........................................................2
(G) Clé d'aile (tube carbone Ø30mm) ...................................................................1
PIECES EMPENNAGES
(A) Empennage horizontal ................................................................................... 1
(B) Fixation empennage horizontal (vis Chc M4x40mm+rondelle) ................ 1set
(C) Dérive .............................................................................................................. 2
(D) Fixation dérive (vis Chc M3x20mm+ rondelle)....................................... 4 sets
(E) Barre de renfort dérive ................................................................................... 2
(F) Fixation barre de renfort dérive (vis Chc M3x20mm+2rondelles+écrou
Nylstop M3 + vis Chc M3x20mm) ................................................................. 2 sets
(G) Fixation servo direction (1 trappe+2 blocs bois dur+4 vis à bois
2,2x12mm) .................................................................................................... 2 sets
(H) Tringlerie de direction (acier Ø2x30mm+chape à rotule
M2+écrou+rondelles) .................................................................................. 2 sets
(I) Guignol de direction.......................................................................................... 2
(J) Tringlerie de profondeur (acier Ø2x75mm+chape à rotule
M2+écrou+rondelles) .................................................................................... 1 set
(K) Guignol de profondeur .................................................................................... 1
WINGS PARTS
(A) Wing (with aileron and flap installed on their hinge point to be glued)
.............................................................................................................(L/R) 1 each
(B) Ailerons pushrod (steel Ø2x65mm) ................................................................2
(C) Flaps pushrod (steel Ø2x50mm) ....................................................................2
(D) Ball clevis with screws (M2x10 screw+nut+washer) ............................ 8 sets
(E) Ailerons and flaps control horn .......................................................................4
(F) Wing screw attachment (plastic M4x25) .........................................................2
(G) Wing joiner (Ø30mm carbon tube) ..................................................................1
TAIL PARTS
(A) Horizontal empennage ................................................................................... 1
(B) Horizontal empennage fixing (SH screw M4x40mm+washer) ................. 1set
(C) Vertical tail ....................................................................................................... 2
(D) Fin fixing (SH screw M3x20mm+washer) ............................................... 4 sets
(E) Fin reinforcement bar ...................................................................................... 2
(F) Fin reinforcement bar fixing (SH screw M3x20mm+2 washers+lock nut
M3+SH screw M3x20mm .............................................................................. 2 sets
(G) Rudder servo fixing (1 hatch+2 hard wood blocks+4 tapping screws
2,2x12mm) .................................................................................................... 2 sets
(H) Rudder pushrod (steel Ø2x30mm+M2 ball link+nut+washers) ........... 2 sets
(I) Rudder control horn ......................................................................................... 2
(J) Elevator pushrod (steel Ø2x75mm+M2 ball link+nut+washers) ............1 set
(K) Elevator control horn ...................................................................................... 1
55
CONTENU DU KIT
PIECES TRAIN D'ATTERRISSAGE
(A) Train avant amorti (avec amortisseur à gaz et roue) .............................1 set
(B) Fixation train avant (vis Chc M4x25mm) ........................................................4
(C) Tringlerie dirigibilité .................................................................................. 1 set
(D) Train principal.................................................................................................. 1
(E) Fixation train principal (vis Chc M4x25mm+rondelle) ............................ 4 sets
(F) Axe de roue train principal (avec 2 bagues d'arrêt de roue) ................. 2 sets
(G) Roue train principal ........................................................................................ 2
PIECES CROCHET DE REMORQUAGE
(A) Crochet de remorquage (crochet+tige un bout fil.+chape M2+4 vis
M3x15mm+4 rondelles .................................................................................. 1 set
PIECES MOTEUR
(A) Fuselage ......................................................................................................... 1
(B) Capot moteur .................................................................................................. 1
(C) Fixation capot moteur (vis à bois 3x12mm) ...................................................6
(D) Tringlerie des gaz...................................................................................... 1 set
(E) Chape à rotule avec visserie ..................................................................... 1 set
(F) Domino ............................................................................................................ 1
PIECES VERRIERE
(A) Verrière .................................................................................................... 1 set
(B) Vis spéciaux fixation verrière ..........................................................................2
DIVERS
Notice de construction .......................................................................................... 1
KIT CONTENT
LANDING GEAR PARTS
(A) Nose gear (with gas shock and wheel) ....................................................1 set
(B) Nose gear fixing (SH M4x25mm) ....................................................................4
(C) Steering pushrod ...................................................................................... 1 set
(D) Main gear ........................................................................................................ 1
(E) Main gear fixing (SH M4x25mm+washer) .............................................. 4 sets
(F) Main gear wheel axis(with 2 wheel stoppers) ......................................... 2 sets
(G) Main gear wheel .............................................................................................. 2
REMOTE TOWING HOOK PARTS
(A) Remote towing hook (hook+one side thread. rod+M2 clevis+4 M3x15mm
screws+4 washers .......................................................................................... 1 set
ENGINE PARTS
(A) Fuselage ......................................................................................................... 1
(B) Engine cowl ..................................................................................................... 1
(C) Engine cowl fixing (self-tapping screw 3x12mm) ............................................6
(D) Throttle pushrod ....................................................................................... 1 set
(E) Ball link with screws................................................................................... 1 set
(F) Rod stopper ..................................................................................................... 1
CANOPY PARTS
(A) Canopy ...................................................................................................... 1 set
(B) Specialized screw canopy attachment ............................................................2
VARIOUS
Construction manual .............................................................................................. 1
7
Publicité
Table des Matières
