Operation; Operation Modes - GBC FOTON 30 Mode D'emploi

OPERATION

OPERATION MODES:

AUTO FEED / AUTO CUT
Note: Best for standard paper sizes printed on 80-120
gsm paper.
1. Press the POWER button to turn the machine ON.
The machine will automatically start in Auto Feed /
Auto Cut mode.
2. Place your document(s) in the FEED TRAY.
3. Slide the Side Guides to fit your document(s) to
minimise skew during lamination.
4. Press the RUN button:
Note: If RUN is pressed before the machine has
completely warmed up, the status bar will be AMBER
blinking in a sequence. The laminator has accepted the
command and will start automatically when machine
reaches proper temperature.
5. Document(s) will be automatically laminated and
automatically trimmed as they exit the machine.
Note: If you hit stop while the document is still feeding
through the laminator, the machine will finish laminating
the document before stopping.
MANUAL FEED / AUTO CUT
Note: Best for standard rectangular paper sizes on heavy
paper stocks that won't Auto Feed.
1. Press the POWER button to turn the machine ON.
2. Select the Manual Feed / Auto Cut mode by pressing
the Mode button.
3. Wait for the machine to reach proper temperature:
solid green STATUS light.
4. Place only the first document in the FEED TRAY.
The document must be placed in the centre of the
Feed Tray and far enough into the feeder to grab your
document.
5. Press the RUN button. The document will begin to
feed into the laminator.
6. After your first document begins laminating, wait for
the MANUAL FEED indicator to illuminate green.
Once illuminated, the machine can be manually fed
the next document. Repeat this process one sheet at
a time until the job is complete.
7. Documents will be manually laminated and
automatically trimmed as they exit the machine.
8. After the final document has been cut and exits the
machine will automatically stop.
MANUAL FEED / MANUAL CUT
Note: This mode is best used for odd-shaped or non-
rectangular documents that won't Auto Feed.
1. Press the POWER button to turn the machine ON.
2. Select the Manual Feed / Manual Cut mode by
pressing the Mode button.
9
3. Wait for the machine to reach proper temperature:
solid green STATUS light.
4. Place only the first document in the FEED TRAY.
The document must be placed in the centre of the
Feed Tray and far enough into the feeder to grab your
document.
5. Press the RUN button. The document will begin to
feed into the laminator.
6. After your first document begins laminating, wait for
the MANUAL FEED indicator to illuminate green.
Once illuminated, the machine can be manually fed
the next document. Repeat this process one sheet at
a time until the job is complete.
7. Press the CUT button to cycle the trimmer anytime
you want to cut the film.
Note: It is recommended to press the CUT
button after you see the entire document exit
the machine to avoid cutting the document.
8. After the final document has exited the machine,
press the STOP button to stop the lamination
process.
9. Once lamination has stopped, press CUT to cut the
remaining film that has exited the machine.
CARTRIDGE FILM LOADING
(Reference Images 1-4 to demonstrate process)
CAUTION: the following procedure might
be performed while the laminator is hot. Use
extreme caution.
1. Open Laminator Door: Open the laminator door by
fully raising the silver latch on the top of the machine
and pull up until door fully opens.
2. Remove Cartridge: Lift upward on the cartridge
handle to remove the installed cartridge.
CAUTION: full cartridges tend to be heavy
3. Insert Cartridge: Insert replacement cartridge by
aligning edges of cartridge over grey channel guide in
laminator and lowering.
Note: Film leader should be inserted away from the feeder,
facing towards the exit of the machine.
4. Close Laminator Door: Close the laminator door by
gently lowering the door and fully close the silver latch
on top. DO NOT push down on the laminator door to
close; use the latch.
5. Ensure Cartridge is Fully Inserted: Film Empty
indicator will be illuminated when no cartridge is
installed or if the cartridge is not fully seated on the
bottom.
Note: When the laminator reaches proper temperature,
the machine will feed approximately 23cm of film to
eliminate potential wrinkles in the film.