TESY CN04 Notice D'utilisation page 20

•
Press the button
EN •
By pressing the buttons
the same time for 10 seconds, „_ _ __" flashes on the display
and the symbols rotate. The appliance returns to „Factory
settings".
•
Turn on the WIFI module.
Note: Whether the module is switched on is indicated by a
steady Wi-Fi symbol on the control panel.
•
Turn on the wireless network of your device;
Note: In order to prevent unauthorized access to the wireless
network of your appliance, the network is available (visible)
for a period of 5 minutes after the initial power-on or reset. If you
exceed this time it is necessary to reactivate/restart the wireless
network of your appliance – see „Instructions for use and storage"
– „Factory settings reset" function.
•
Press «NEXT»
5.2. Use your your smart phone (‚i-pad, laptop) to activate the function for
detecting wireless networks (Wi-Fi)
Manually enter the wireless network name of the device
5.3.
, or scan the QR code.
(TCHхххххххх)
Note: The wireless network name is case sensitive.
Note: The QR code and the wireless network name are
marked on a label next to the rating plate of the appliance.
Press «NEXT». The app automatically connects to the wireless
5.3.
network of the device.
A new screen opens - local interface Indoor connect. In order
5.4.
to connect the converter to your home Wi-Fi network and from
there to the internet, complete the following sequence of steps
from submenu Quick setup
1. Connection >> 2. Date and time >> 3. mytesy.com >> 4.
Temperature correction >> 5. Wi-Fi Security
Note: After finishing Quick setup, if you want to proceed again
with the settings of the convector, you must select menu Manual
setup.
/QUICK START D/
II. CONTROL OF THE CONVECTOR THROUGH THE BUILT-IN WI-FI
COMMUNICATION DEVICE /QUICK START E/:
The convector can be controlled via the built-in Wi-Fi communication
device via the Control panel menu.
Control panel - Choose operation mode
Open window (only for model CN04) - The appliance is equipped
with an integrated electronic device which automatically switches off the
heating power if a sharp decrease of temperature is found in the room,
when a window or a door is open. When the temperature in the room
begins increasing the heating will be automatically restored.
Lock device - You can lock the buttons, in order to prevent any
changes to the settings.
Anti-frost - If the room temperature falls below 5 degrees Celsius and
the convector is off (the red LED is not lit, but the mechanical switch is in
position "I" (On) ), the heater will be automatically switched on in order to
prevent from freezing.
Basic mode - Choose from your desired temperature. Once the convector
reaches it, it will keep it.
Delay start - Тhe appliance is in Off mode, you can use the arrows to set
the time when the appliance is to be switched on within 96 hours. Once
the time has passed, the convector will always be launched in „Manual
program".
Weekly program - This program allows you to configure the temperature
of your convector at any time of the week throughout the week. For each
hour, you can set one of the three states of the convector.
Settings of weekly program /QUICK START E 4./– you should enter the
following
parameters:
•
Start and end time;
•
Desired temperature;
•
Week days;
•
Button Save.
Note: The Power button must be in the ON position
the weekly programmer.
20 Operation and Storage Manual of Panel Heater
to turn off the device;
and on the convector panel at
from menu Settings:
/QUICK START C/
, in order to set
Note: Periods out of the set time periods are in OFF mode.
Adaptive start - Convector will start early to reach the set temperarure in
the specified time range.
Additional functions:
Power calculator /QUICK START F/- It provides information about
the instantaneous power consumption of the convector from the time of
the first switching on.
Device info /QUICK START G/ - It provides information about
device's software.
Operation via the internet
II.
/QUICK START H/
From the list of registered devices, select the device you want to
control.
A screen opens with controls that allow you to select the mode of
operation, to monitor the current status of the appliance, to make
a detailed reference of the consumed energy.
To be able to operate you device, it must be switched on .
1.
Manual operation mode – press the
2.
When you select the "Manual"mode
temperature in the room to be heated by moving the slider left
and right. During heating the message "HEATING" will appear on
the screen. When the appliance has reached the set value the
message "READY" will appear on the screen.
Weekly programmer mode -
3.
In Program mode , the appliance functions when the
settings in the Weekly Program menu have been done. (week
programmer). You can exit this mode by switching the appliance
on or off from the ON/OFF button, or by changing the setting of
the set temperature, i.e. you are in the manual settings regime.
To see the time schedule of each program and to change it, if
needed, press the button (see P.7).
21
Adaptive start - to activate, press
4.
a function which predicts and initiates the optimal start of heating
up in order to reach the set temperature in the desired time.
Open window – to activate, press
5.
Anti-frost function – to activate/deactivate, press
6.
Weekly programmer
7.
To see the schedule of operation for each program and if
necessary, to change it, press the
A diagram of the weekly schedule of operation of the electrical
7.1.
convector for the selected program opens. Select a day from the
diagram to see detailed schedule and edit the current settings.
A new screen opens where you can:
7.2.
•
Select a program;
•
Select day of the week;
•
Scale with equivalent of temperature. Using the slider on the
scale you can select the preferred reading ;
•
Bar chart visualizing the setting for operation by hours.
Algorithm for creating a schedule for operation of an electrical
convector:
1. Select a program of operation;
2. Select day of the week;
3. Select the temperature using the slider on the right of the
screen.
4. Select the bar for the hour you want to set up. The length of the
bar changes and the set temperature is written in it.
Using the button in the upper right corner of the screen
7.3.
+
you can copy the current settings for other days of the week. A
new screen opens where you can select all days to which you want
to copy the settings.
Activity over past 24 hours.
8.
button.
, you can set the desired
- Adaptive start control is
(only for model CN04)
button.
21