Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ABOUT THE BODY SCANNING FUNCTION
Additional Information
Body Scanning
(1) As the electronic tone that accompanies the body search function sounds,
the massage heads will rise up the back until they reach the area behind
(2)
the neck.
(2) The massage heads will tilt forward so that they are positioned over the
(3)
shoulders. (If the shoulder position is incorrect the massage heads will
rise again and then repeat the shoulder alignment movement.)
(1)
(3) The massage heads will descend to the level of the shoulders.
(4) Soft Tapping
(4) A soft tapping massage is performed at the level of the shoulders, which
lasts for approximately 15 seconds.
When the Body Scanning Function is Not Completed Successfully
• A recorded voice message will announce, "In the interests of safety, the massage will now finish because
an occupant could not be detected in the chair." during the body scanning.
This may occur in the following situations:
1. Pressure against the backrest cannot be detected because no one is sitting in the chair.
2. Pressure against the backrest cannot be detected because the occupant's head and back are not
touching the backrest.
3. Pressure against the backrest cannot be detected because the occupant is wearing heavy clothing or an
object such as a cushion has been placed between the occupant's back and the backrest.
Sit as far back in the seat with your head on the pillow and
press
again to start the body scanning.
When the Soft Tapping Massage Does Not Start
• If the body scanning is performed at the highest height, it will stop for a few seconds and the soft tapping
massage will not be carried out.
To adjust the shoulder position, do so after the massage has begun.
When Changing the Occupant in the Middle of a Massage
• Press
once to finish the massage then start again as the shoulder position will change.
Additional Information
Pressure Feedback Function
The strength of the massage (pressure level) is automatically adjusted if it is too much or too little.
• The standard body pressure level varies according to the strength of the program selected.
• If you lift your back or stand up in the middle of a massage, the body pressure level detected will be zero
thus causing the massage to finish.
Pressure Feedback in Shoulder Area
• When a massage program is used, the body pressure level at the top of the shoulders is detected just
before the start of a massage at the top of the shoulders. If the body pressure level is different from that of
the previous massage a soft tapping massage will begin.
36
All manuals and user guides at all-guides.com
TROUBLESHOOTING
PROBLEM
Problem
Motor Noises
• It sounds and feels like the massage heads are
straining to get over wrinkles in the cloth.
• The motor groans when it comes under load.
• There is excessive noise during Tapping. (The noise
is greater at the top of the massage lounger.)
• There is a creaking noise when the massage heads
are in operation.
• There is a sound when the vibration action is selected.
• There is a rattling sound when the massage heads
move up or down.
• The belt can be heard rotating.
• There is a rubbing sound produced by the massage
heads rubbing on the seat fabric.
• There is a noise when the back cushion moves over
the armrest when the seat is reclining.
• There is a noise when I sit down.
• There is a strange sound when the massage heads
move in and out.
• When the power switch is turned on there is a
humming sound.
• Air massage-related sounds.
There is a hissing sound of air escaping.
There is a humming sound from the pump.
• The legrest rattles.
• There is an unstable sound when air escapes during
the leg stretch.
The massage heads stop during operation.
The massage heads do not come up to the
shoulder or neck.
The height of the left and right massage
heads is different.
The air in the seat is not being released.
It is not possible to recline the unit.
The legrest cannot be raised or lowered.
Cause and Remedy
These sounds are perfectly normal and will not have
any effect on the operation of the unit.
If excessive force is applied to the massage heads
during operation, in the interests of safety the
massage heads may stop moving.
If all markings and buttons on the control panel start
to flash, which is extremely unusual, turn off the power
switch, wait for approximately 10 seconds and then
turn the power switch on again.
If the massage heads stop again, position yourself so
that your back is not completely in contact with the
backrest.
The position of the massage heads is incorrect.
(See Page 16)
An alternating tapping method is employed, which
means that this phenomenon will naturally occur.
There is nothing wrong with the unit.
If the power cord is unplugged or there is a power
outage while air massage is being carried out, the air
will be trapped in the unit. The air will automatically be
released when the power cord is plugged back in again
(or when the power comes back on).
If the unit encounters an obstacle or if excessive force
is exerted on it during operation, in the interests of
safety the unit will come to a stop.
If all markings and buttons on the control panel start
to flash, which is extremely unusual, turn off the power
switch, wait for approximately 10 seconds and then
turn the power switch on again.
37
Publicité
Table des Matières
