Getting The Appliance Ready For Use - Barbecook VICTOR 223.7020.000 Mode D'emploi

Your pressure regulator and coupling may be different
from the ones in the illustrations.
6. Do one of the following:
• If you detect a leak, continue as described in "In case of
a gas leak".
• If there are no leaks, close the gas supply, rinse all
components thoroughly with water and dry them well.
5.6 In case of a gas leak
1. Close the gas supply and do one of the following:
• If you detected a leak on one of the connections, tighten
that connection.
• If you detected a leak on the cylinder or hose, replace
the cylinder or hose.
2. Recheck the connection or component on which you
detected the leak.
3. If the leak is not repaired, contact a Barbecook dealer. Do
not use the appliance until the leak is repaired.
For a list of nearby Barbecook dealers, refer to
www.barbecook.com.
6 GETTING THE APPLIANCE
READY FOR USE
6.1 Before each use
Do not use the Plancha before you have read, understood and
checked all information in this manual. Ensure that:
• The Plancha is correctly installed
• There is no leak in the gas supply (see "5)
• The burners are correctly installed, the venturi tubes are
properly placed over the openings of the gas valves, and
there are no obstructions (see safety information and
cleaning of the burners)
• None of the gas supply hoses can come into contact with
a hot surface
• Your Plancha is installed in a safe place
6.2 Lighting the burners
. To light the burners with the electrical igniter, you have
to install an AA battery in the igniter. That battery is not
supplied with the appliance. You find the battery case of
the igniter on the control panel of your appliance.
• Do not lean directly over the Plancha when lighting the
burners. The control knobs on the Plancha must be in the
OFF position.
• Never try to light the 2 burners at once.
6.3 Lighting the burners using the igniter
• Set the control knob of one burner to
• Press the ignitor button and keep pressing the ignitor button
until you have verified that the burner has ignited (noise &
visible through view holes side panel).
• lf the burner does not light within 5 seconds, set its control
knob to OFF, close the gas supply and wait 5 minutes.
This allows any accumulated gas to escape
• Retry lighting the burner, if it still does not light, refer to
"Troubleshooting" to determine the cause of the problem.
• Once one burner is lit, light the other burner by setting the
control knob to high.
6.4
On left & right-side panel there is a view/ignitor hole. You can
light the burners using a long match if the electronic ignition does
not
•
•
•
•
6.5
The second burner is lit in the same way as the first.
6.6
Each time you light a burner, you have to check its flames. A
perfect flame is almost completely blue, with some yellow at the
top. Sporadic yellow flames are normal and not harmful.
If there is something wrong with the flames, do one of the
following to solve the problem:
HIGH.
www.barbecook.com
Lighting the burners using a match
work.
Open the tap on the gas cylinder.
Hold the lighted match through the
from the burner.
Press in the desired knob and turn to 'High'. The fire should
light within five seconds. If not, turn the knob off and wait
for five minutes to allow the gas to disperse.
Repeat above steps. If the burner still fails to ignite
after three attempts, read the "Troubleshooting"
section.
Lighting the other burner
Visual check of the flames
If the flames are...
Low and entirely yellow
Higher than the bowl
LOW
hole about 13 mm
Do the following...
1. Immediately close the gas
supply and set all control
knobs to OFF.
2. Refer to "Troubleshooting"
to determine the cause of
the problem. Most likely, the
venturis are blocked.
1. Immediately close the gas
supply and set all control
knobs to OFF.
2. Wait 5 minutes to allow any
accumulated gas to escape.
3. Relight the burner(s).
4. If the problem persists, refer to
"Troubleshooting" to determine
the cause of the problem.
HIGH
7