Ecotop ExtraCT 06490 Mode D'emploi page 7

WINGS PARTS
(A) Wing (with aileron installed on easy hinges) ..................................(L/R)1 each
(B) Wing joiner (plywood)...................................................................................... 2
(C) Aileron pushrod (2.0x100mm) .......................................................................2
(D) Ball link ............................................................................................................ 4
(E) Control horn (fiberglass) ................................................................................. 2
(F) 2x10mm screw ................................................................................................ 4
(G) 2mm washer .................................................................................................... 8
(H) 2mm nut .......................................................................................................... 4
(I) 3x15mm screw ................................................................................................. 4
(J) 3mm washer D=8mm ...................................................................................... 4
(K) Fiberglass tape ................................................................................................ 1
(L) Winglet ............................................................................................................. 2
LANDING GEAR PARTS
(A) Fuselage .......................................................................................................... 1
(B) Main gear ........................................................................................................ 1
(C) 3x12mm cap screw ......................................................................................... 4
(D) 3mm washer .................................................................................................... 4
(E) Wheel cover ............................................................................................... 1 set
(F) Wheel axle .................................................................................................. 1 set
(G) 60mm wheel .................................................................................................... 2
(H) 4mm wheel collar ............................................................................................ 2
(I) 4mm nut ........................................................................................................... 2
(J) 4mm lock nut .................................................................................................... 2
(K) 2x10mm self tapping screw ............................................................................2
ENGINE MOUNTING PARTS
(A) Engine mount ............................................................................................ 1 set
(B) 4x30mm cap screw ......................................................................................... 4
(C) 4x25mm self tapping screw ............................................................................4
(D) 4mm washer .................................................................................................... 4
(E) Throttle pushrod L=250mm ...........................................................................1
(F) Guide pipe....................................................................................................... 1
(G) Adjust stopper ................................................................................................. 1
FUEL TANK PARTS
(A) Fuel tank ......................................................................................................... 1
(B) Tank cap .............................................................................................. large / 1
(C) Tank cap .............................................................................................. small / 1
(D) Rubber plug..................................................................................................... 1
(E) Aluminium pipe .................................................................................... long / 1
(F) Aluminium pipe ...................................................................................short / 2
(G) Fuel line ........................................................................................................... 1
(H) Clunk ................................................................................................................ 1
(I) 3x28mm self tapping screw ................................................................. long / 1
KIT CONTENT
HORIZONTAL STAB PARTS
(A) Horizontal stabilizer (with easy hinges) .........................................................1
(B) Elevator (R&L) .......................................................................................... 1 set
(C) Elevator joint (4mm music wire) .....................................................................1
(D) Pushrod (2.0x150mm) ................................................................................... 1
(E) Control horn ................................................................................................... 1
(F) Ball link ........................................................................................................... 2
(G) 2x10mm cap screw ......................................................................................... 2
(H) 2mm washer .................................................................................................... 4
(I) 2mm nut .......................................................................................................... 2
(J) Stab strut ........................................................................................................ 2
(K) 3x8mm self tapping screw .............................................................................. 4
VERTICAL EMP . PARTS
(A) Vertical fin........................................................................................................ 1
(B) Rudder (with easy hinges) .............................................................................. 1
(C) Pushrod (2.0x150mm) ................................................................................... 1
(D) Control horn .................................................................................................... 1
(E) Ball link ............................................................................................................ 2
(F) 2x10mm cap screw ......................................................................................... 2
(G) 2mm washer .................................................................................................... 4
(H) 2mm nut .......................................................................................................... 2
(I) Tail gear ...................................................................................................... 1 set
(J) 3x10mm self tapping screw .............................................................................2
(K) 2mm wheel retainer ........................................................................................ 1
(L) 25mm wheel .................................................................................................... 1
COWLING PARTS
(A) Cowling ............................................................................................................ 1
(B) Cowl block 1 .................................................................................................... 2
(C) Cowl block 2 ..................................................................................................... 2
(D) Former doubler ............................................................................................... 1
(E) 2.6x10mm self tapping screw .........................................................................5
FINISHING PARTS
(A) Canopy (ready-fitted on its frame) ..................................................................1
(B) 4x50mm screw ................................................................................................ 2
(C) 4mm washer .................................................................................................... 2
(D) Wing bolt reinforcement .................................................................................. 1
(E) 3x12mm cap screw ......................................................................................... 2
(F) 3mm washer .................................................................................................... 2
(G) Stickers sheet .................................................................................................. 1
(H) Velcro® band ................................................................................................. 1
7