Kohler actronic Serie Mode D'emploi page 15

Connecting the accu and activating the
1. Check if RC-frequency is free. If it is, switch on your transmitter.
2. Make sure throttle is at off-position ("motor off").
3. Switch on receiver.
4. Connect accu to
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
5. Now you have to activate
1s it has to be off if everything is o.k. If it keeps shining there could be several reasons:

The transmitter is off or it does not work.

The receiver is off or it does not work.

Receiver and transmitter work at different frequencies or one quartz is defect.

The controller is not connected to the receiver or the connection is broken.

If non of the cases above are true and the LED still keeps shining you have to en-
gage the servo reverse function of your transmitter. How to do this, look at the
transmitters manual. At off-position
mum-position. Therefore you may mave to enable the servo reverse function of your
transmitter.
6. Now the LED should be off after 1s after connection of the accu.
captured the neutral-position of throttle.
7. Engage throttle to maximum. After a short delay LED turns on and off again. At this
moment has captured the maximum-position of throttle.
 ¢       ©  
8. Now pull throttle to neutral-position. The LED will blink 4 times to tell you that
is now ready. You are able to start the motor now.
9. The extrapolates the throttle curve for backwards direction like you adjusted
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
the forward direction. If your neutral-position is located out of the middle with a longer
distance between neutral- to maximum-forward-position the maximum backward
throttle is reduced. The more you want to reduce maximum backward throttle the more
you have to set the neutral-position out of the middle towards the extremum of back-
wards throttle position.
10.Please keep in mind that this procedure has to be repeated every time you connect the
accu to the
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
tees to avoid starting the motor by mistake when connecting the accu.
If you still make a mistake while connecting or activating nothing will happen except
you connect the accu directly at the motor or you connect the accu with wrong polarity
- the controller can do nothing in those cases of abuse. So, if there creeps a mistake
during the starting procedure the controller strikes and the motor won' t r un. In this case
unplug the accu from the controller and make a complete check.
Switch-off procedure of the remote control equipment
Always maintain the following order to switch off your equipment:
1. Make sure motor is not running.
2. Disconnect accu from
3. Switch off receiver.
4. Switch off transmitter.
K hler Elektromotoren GbR
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
.
. Look at the LED, it must be on. After approximately
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
. These adjustments won' tbe saved! Only this procedure guaran-
.
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
- Betriebsanleitung/operating instructions
 © ! " # © $ %
in car mode (car/marine version)
needs a shorter impulse than at maxi-
has now
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
¢ ¡ £ ¤ ¥ § ¦ © ¨ ¡
Seite/page 15