GYS WS-4R Mode D'emploi page 8

WARNING - SAFETY RULES
GENERAL INSTRUCTIONS
Read and understand the following safety recommendations before using or servicing the unit.
Any change or servicing that is not specified in the instruction manual must not be undertaken.
The manufacturer is not liable for any injury or damage caused due to non-compliance with the instructions featured in this manual .
In the event of problems or uncertainties, please consult a qualified person to handle the installation properly.
Read the welding machine's instruction manual before using the wire feeder.
ENVIRONMENT
This equipment must only be used for welding and gouging operations in accordance with the limits indicated on the descriptive panel and/or in
the user manual. The operator must respect the safety precautions that apply to this type of welding. In case of inedaquate or unsafe use, the
manufacturer cannot be held liable for damage or injury.
This equipment must be used and stored in a place protected from dust, acid or any other corrosive agent. Operate the machine in an open, or
well-ventilated area.
Operating temperature:
Use between -10 and +40°C (+14 and +104°F).
Store between -20 and +55°C (-4 and 131°F).
Air humidity:
Lower or equal to 50% at 40°C (104°F).
Lower or equal to 90% at 20°C (68°F).
Altitude:
Up to 1000 meters above sea level (3280 feet).
INDIVIDUAL PROTECTIONS AND OTHERS
Arc welding can be dangerous and can cause serious injury or even death.
Welding exposes the user to dangerous heat, arc rays, electromagnetic fields, risk of electric shock, noise and gas fumes. People wearing pacemakers
are advised to consult a doctor before using the welding machine. Protect yourself and others. Ensure the following safety precautions are taken:
In order to protect you from burns and radiations, wear clothing without cuffs. These clothes must be insulating, dry, fireproof, in
good condition, and cover the whole body.
Wear protective gloves which guarantee electrical and thermal insulation.
Wear welding
the application).
It may be necessary to install fireproof welding curtains to protect the area against arc rays, weld spatter and sparks.
Inform people who are around the working area to never look at the arc ray or the molten metal, and to wear protective clothes.
Wear ear protection if the work exceeds the authorised noise limit. The same applies to anyone in the welding area.
Keep
Never remove the safety covers from the cooling unit when the machine is plugged in. The manufacturer is not liable for any injury
or damage due to non-compliance with the safety precautions.
Parts that have just been welded will be hot and may cause burns when touched. During the maintenance of the torch, make
sure that the torch has sufficiently cooled down and wait at least 10 minutes before any operation. When using a water-
cooled torch, make sure that the cooling unit is switched on to avoid any burns that could potentially be caused by the liquid.
It is important to secure the working area before leaving it to ensure protection of the goods and the safety of people.
WELDING FUMES AND GAS
The fumes, gases and dust produced during welding are hazardous. It is mandatory to ensure adequate ventilation and/or
extraction to keep fumes and gases away from the work area. An air fed helmet is recommended in cases of insufficient air supply
in the workplace.
Check that the air intake is in compliance with safety standards.
Caution, welding in small work areas requires surveillance from a safe distance. Welding certain pieces of metal containing lead, cadmium, zinc,
mercury or beryllium can be extremely toxic. The user will also need to degrease the workpiece before welding.
Gas cylinders must be stored in an open or ventilated area. The cylinders must be in a vertical position secured to a support or trolley.
Do not weld in areas where grease or paint are stored.
8
protective gear for
Protect your eyes
hands, hair and clothes
WS-4R / WS-4L
the whole body: hood,
during cleaning procedures.
away from moving
gloves, jacket, trousers...
Contact lenses are
parts such as
EN
(variable, depending on
prohibited during use.
fans, and engines.