Ecotop Baron Mode D'emploi page 7

PIECES AILES
(A) Aile (avec aileron monté sur charnières à coller) ............... (G/D) 1 de chaque
(B) Aile - tronçon central ...................................................................................... 1
(C) Trappe servo aileron ....................................................................................... 2
(D) Taquet bois dur ............................................................................................... 4
(E) Vis fixation trappes (vis à bois 2,2x8mm) ......................................................8
(F) Tringlerie ailerons (acier Ø2x60mm) ..............................................................2
(G) Chape rotule avec visserie (vis M2x10+écrou+rondelle) ..................... 2 sets
(H) Guignol ailerons ...................................................................................... 2 sets
(I) Fixation d'aile (vis Chc acier M3x25mm+rondelle) ................................. 4 sets
(J) Clé d'aile (tube carbone) .................................................................................. 1
PIECES EMPENNAGES
(A) Fuselage (avec trappe avant) .........................................................................1
(B) Empennage horizontal .............................................................................. 1 set
(C) Empennage vertical ................................................................................... 1 set
(D) Commande de profondeur ........................................................................ 1 set
(E) Commande de direction ............................................................................ 1 set
(F) Chape rotule avec visserie (vis M2x10+écrou+rondelle) ...................... 4 sets
(G) Guignol de commande ............................................................................. 2 sets
PIECES TRAIN D'ATTERRISSAGE
(A) Train ................................................................................................................ 1
(B) Roue ................................................................................................................ 2
(C) bague d'arrêt de roue et vis ................................................................... 2 sets
(D) Cavalier nylon .................................................................................................. 4
(E) Vis de fixation (vis à bois 2,8x14mm) .............................................................8
(F) Béquille de queue ............................................................................................ 1
WINGS PARTS
(A) Wing (with aileron installed on its CA hinges to be glued) ............(L/R) 1 each
(B) Wing - Center section ...................................................................................... 1
(C) Hatch ailerons servo ....................................................................................... 2
(D) Hard wood block ............................................................................................. 4
(E) Hatch fixing screw (wood screw 2.2x8mm) ....................................................8
(F) Ailerons pushrod (steel Ø2x60mm) ................................................................2
(G) Ball clevis with screws (M2x10 screw+nut+washer) ............................. 2 sets
(H) Ailerons control horn .............................................................................. 2 sets
(I) Wing screw attachment (socket head screw M3x25+washer) ................ 4 sets
(J) Wing joiner (carbon tube) ................................................................................ 1
TAIL PARTS
(A) Fuselage (with front hatch) ............................................................................. 1
(B) Horizontal tail ............................................................................................ 1 set
(C) Vertical tail ................................................................................................. 1 set
(D) Elevator pushrod....................................................................................... 1 set
(E) Rudder pushrod ........................................................................................ 1 set
(F) Ball clevis with screws (M2x10 screw+nut+washer) ............................. 4 sets
(G) Control horn ............................................................................................ 2 sets
WINGS PARTS
(A) Landing gear ................................................................................................... 1
(B) Wheel ............................................................................................................... 2
(C) Wheel collar/set screw ............................................................................. 2 sets
(D) Nylon strap ...................................................................................................... 4
(E) Attachment screw (wood screw 2.8x14mm) ...................................................8
(F) Tailskid ............................................................................................................. 1
Légende/Legend
l Non inclus/not included
Anglais/English
H
CONTENU DU KIT
PIECES MOTEUR THERMIQUE
(A) Capot moteur fibre de verre ............................................................................1
(B) Taquet bois dur ............................................................................................... 4
(C) Fixation capot (vis à bois 2,2x12mm) .............................................................4
(D) Bâti moteur ajustable ................................................................................ 1 set
(E) Fixation bâti (vis Chc M4x20+rondelle+écrou à griffes M4) ................. 4 sets
(F) Fixation moteur (vis Chc M3x25+rondelle+écrou nylstop M3) ............. 4 sets
(G) Commande de gaz (CAP+gaine) .............................................................. 1 set
(H) Domino ............................................................................................................ 1
(I) Réservoir .................................................................................................... 1 set
(J) Sangle Velcro® ................................................................................................ 2
PIECES MOTEUR ELECTRIQUE
(A) Capot moteur fibre de verre .........................................................................(1)
(B) Taquet bois dur ............................................................................................ (4)
(C) Fixation capot (vis à bois 2,2x12mm) ..........................................................(4)
(D) Bâti moteur CTP .............................................................................................. 1
(E) Fixation bâti (vis Chc M3x20+rondelle+écrou à griffes M3) ................. 4 sets
(F) Sangle Velcro® ............................................................................................ (2)
PIECES FINITION
(A) Buste pilote ..................................................................................................... 1
(B) Faux moteur .................................................................................................... 1
(C) Elastique à chapeau ............................................................................5 mètres
(D) Tube à sertir..................................................................................................14
(E) Vis à bois 2.2x8mm .......................................................................................14
(F) Mât de cabane ................................................................................................. 2
(G) Sommet du mât ............................................................................................... 1
(H) Mitrailleuse ...................................................................................................... 1
DIVERS
Planche d'autocollants .......................................................................................... 1
Notice de construction .......................................................................................... 1
KIT CONTENT
H
IC ENGINE PARTS
(A) Fiberglass engine cowl .................................................................................... 1
(B) Hard wood block ............................................................................................. 4
(C) Cowl fixing (wood screw 2.2x12mm) ...............................................................4
(D) Adjustable engine mount .......................................................................... 1 set
(E) Mount fixing (SH screw M4x20+washer+M4 tiger nut .......................... 4 sets
(F) Engine fixing (SH screw M3x25+washer+M3 lock nut .......................... 4 sets
(G) Throttle linkage (music wire+outer rod) ..................................................1 set
(H) Rod stopper .................................................................................................... 1
(I) Fuel tank ..................................................................................................... 1 set
(J) Velcro® tie ....................................................................................................... 2
MOTOR PARTS
(A) Fiberglass engine cowl ................................................................................. (1)
(B) Hard wood block .......................................................................................... (4)
(C) Cowl fixing (wood screw 2.2x12mm) ............................................................(4)
(D) Plywood motor mount box .............................................................................. 1
(E) Mount fixing (SH screw M3x25+washer+M3 tiger nut .......................... 4 sets
(F) Velcro® tie ................................................................................................... (2)
FINISHING PARTS
(A) Pilot bust ......................................................................................................... 1
(B) Dummy engine ................................................................................................ 1
(C) Rubber string .......................................................................................5 meters
(D) Crimp tube .....................................................................................................14
(E) Wood screw 2.2x8mm ...................................................................................14
(F) Cabane mast .................................................................................................... 2
(G) Top of mast ..................................................................................................... 1
(H) machine gun .................................................................................................... 1
VARIOUS
Stickers sheet ........................................................................................................ 1
Construction manual .............................................................................................. 1
7