Customer Service; Replacing The Battery; Charging The Battery - Peg-Perego John Deere IGOR0088 Utilisation Et Entretien

RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Fit the 2 side inserts of the bonnet in their
respective slots in the chassis, as shown in the
figure.
2 • Position the hood by inserting the hinge into the
seat of the chassis provided (1). Then screw
down the hinge (2). Close the hood and use a
coin to lock the safety catch (3).
3 • Press the two central headlights into place,
paying attention to the 3 corresponding tabs.
4 • Install the two remaining side headlights, again
paying attention to the corresponding tabs.
Attention! The central headlights and side
headlights are not identical: check that the
orientation and shape match before pressing
them into place.
5 • Press the side inserts onto the chassis.
6 • Position the seat in one of the two possible
positions on the seat support that will best suit
the child's height.
Seat position A - low and forward;
Seat position B - high and to the rear.
7 • Secure the seat in the desired position using the
two screws provided.
8 • Slide the two front studs of the seat support
into the relating holes on the frame.
9 • Secure the rear of the seat support to the
excavator frame using the two screws provided.
10 • Position the roll-bar to the excavator by sliding
both ends of the bar into the slots on the rear
mudguards.
Note: the roll-bar should lean slightly towards
the rear of the excavator.
11 • Secure the roll-bar in position with the two
screws supplied (one on each side).
12 • Attach the lights from bottom to top.
13 • Insert two AA 1.5V batteries into the radio,
opening the rear cover (see figure).
14 • Put the radio in place by inserting the two clips
into the chassis under the steering wheel shaft,
fixing it with a screw as shown in the figure.
15 • Press the ring onto the underside of the steering
wheel and the cap.
16 • Push the steering wheel shaft from under the
tractor up until it emerges from the top of the
chassis.
17 • Hold the shaft in this position and insert the
steering wheel.
18 • Fix the steering wheel with the bolt and nut
provided, taking care to insert the bolt into the
round hole and the nut into the hexagonal one.
19 • Press the hubcaps onto the wheels; the larger
ones go onto the front wheels, the smaller ones
onto the rear wheels.
20 • Overturn the bucket as shown in the figure.
Remove the elastic on the loader arm with lever;
then insert the arm spring into the
corresponding point on the bucket.
21 • Slide a washer onto the screw and insert it into
the corresponding holes to connect the bucket
to the loader arm. Slide a second washer onto
the screw, then insert the nut. Tighten with a
screwdriver and pliers. Repeat on the opposite
side.
22 • Install one of the two cross pieces onto the front
part of the loader arms, as shown in the figure.
23 • Fix with the two screws provided (one for each
side).
24 • Insert the second cross piece onto the rear part
of the loader arms.
25 • Fix with the two screws provided (one for each
side).
26 • Put the handle in place as shown in the figure;
the picture in box A shows the CORRECT
position of the lower tab, which should be
inserted into the slot of the loader arm; the
picture in box B shows the INCORRECT
position.
27 • Insert a nut into the hexagonal hole on the inner
part of the handle. Insert a screw onto the
opposite side.
28 • Fix the handle into place by tightening the
screws. Repeat on the opposite side.
29 • Insert a stud into the cavity on the right side of
the bucket, lining up the respective holes.
30 • Remove the elastic tying the metal tension rod
to the lever.
31 • Place the control lever of the loader vertically
and, pressing hard, attach the tension rod to the
bucket.
32 • Place the loader onto the tractor.
33 • Fix the rear part of the loader, as shown in the
figure.
34 • Insert a large washer into the conical washer
bearing as shown in the picture. Put the iron pin
into place, and with the help of a hammer, insert
it into the washer.
35 • Line up the loader holes with those of the cab
and insert the pin.
36 • Place a stud on the opposite side of the pin,
without using any tools.
37 • Complete the attachment of the pin using the 2
washer bearings provided, pressing the 2 parts
hard and simultaneously. Apply the stickers.
38 • To open the battery compartment, lower the
handle completely, detach it and rotate the black
pin of the cab by 180° and lift.
39 • Connect the battery plug to that of the system.
Close the battery compartment, taking care that
the side parts of the cab are on the outside, and
secure by turning the black pin by 180°. The
vehicle is ready for use.
FEATURES AND
INSTRUCTIONS FOR USE
40 • GEAR SHIFT LEVER. The vehicle has three
speeds. ATTENTION: when it is removed from
the packaging, the vehicle only travels in first
gear and in reverse. To use 2nd gear, see figure
41.
41 • Remove the screw in the second gear lock (fig.
A). Turn the lock to the next position (fig. B).
Screw the lock back on. All gears are now
available.
42 • ACCELERATOR PEDAL/ELECTRIC BRAKE. The
brake will automatically be applied when the
foot is lifted off the pedal.
43 • FM RADIO: To switch on, off and adjust the
volume turn knob A. Press the triangular and the
square button (see figure) to select the radio
station.
44 • LOADER: To lower the loader, push the handle
forward as far as it will go.
45 • To raise the loader, pull back the handle and lock
into place.
46 • To turn the bucket forward, pull back the side
lever. Release the lever to return the bucket to
the starting position.

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
47 • Open the battery compartment, as shown in
before. Disconnect the battery power plugs.
48 • Unscrew the two screws of the battery holder
and remove it as shown in the figure. Extract the
battery.
49 • If you possess or have purchased a 12V/12Ah
Peg Perego battery, you should remove the
plastic filler (A) by slipping it off the battery
holder.
50 • Put the new battery into place with the battery
holder, taking care to insert it sideways into the
false motors housing; fix the battery holder in
place with the two screws.
51 • Connect the battery and electrical system plugs.
Close the hood by repositioning the lock, as
shown before.

CHARGING THE BATTERY

WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY. THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
52 • Insert the battery charger plug in a domestic
power socket in accordance with the
instructions enclosed with it. Connect plug B
with the battery charger plug C. When the
battery is charged, remove the battery charger
from the domestic socket, then disconnect plug
C from plug B.
53 • Fully insert plug B into plug A, ensuring that they
click together. Insert the battery holder. Once
finished, always remember to close and lock the
lid of the battery compartment.