Télécharger Imprimer la page

Maintaining The Brakes - Miche FRENI SUPERTYPE RS Manuel D'utilisation Et D'entretien

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Thank you for purchasing the Supertype RS brakes, a product that
offers both safety and functionality over time.
Before proceeding with using the brakes, please read carefully the
following instruction and store them in a safe place for eventually
reusing.
Fac Michelin S.p.A. reserves to modify the content of this manual
without notice. The update version will always be available www.
miche.it.
On our website you will also find information on the other MICHE
and SUPERTYPE products.
TOOLS
(Picture pag.8)
The Supertype RS set of brakes can be mounted onto the frame,
regulated and maintained with the following spanners (not included
in the pack):
• 2-4-5 mm Allen spanner
• Torque wrench
WARNING!
Brake pads assembled on brake set are set for Alloy rim
use only.
WARNING!
If you have any doubt whatsoever regarding your service-
repair ability, please take your bicycle to a qualified repair
shop.
Before any maintenance operations on your brakes, always
wear gloves and protection glasses.
INSTALLING THE BRAKE
• Before positioning the brake, check that the brake pads are su-
itable for the rim
• Fit the brake onto the frame or fork, and tighten the Allen nut (B)
(Pic. 1) using a 5 mm spanner, and then manually centre the brake
with respect to the wheel. Once the brake is centred, close the
release lever (C) (Pic. 1).
During installation, always check that the centre screw on the bra-
ke enters the threaded bushing by at least 6-7 threads. Less scre-
wed threads could cause the centre screw to break when the bike
is being used and therefore cause the brake to detach from the
frame and cause accidents and serious or even mortal injuries.
• Fix the cable by tightening the cable clamp screw (D) (Pic. 2)
with a torque of 5 Nm using a 5 mm Allen spanner. If there is too
much space between the pad and rim on both sides, regulate it by
turning the regulation screw for cable tension (E) (Pic. 2).
Check the cable is correctly fixed in place, as if it is loose or da-
maged it could mean the brakes would no longer work and cause
accidents and serious or mortal injuries.
• The brakes are fitted with a regulation screw (A) (Pic. 1) for cor-
recting the centring of the brake with the wheel, using a 2 mm
Allen spanner.
• Fix the brake to the frame by tightening the nut (B) (Pic. 1) using
the torque wrench with a torque of 10 Nm.
Check that the nut is firmly tightened down because if it works use
when the bike is being used, it could mean the brakes would no
longer work and cause accidents and serious or mortal injuries.
REGULATING AND FIXING THE BRAKE PADS
• Periodically check that the brake pads are 1.5-2 mm away from
the surface of the rim (Pic. 3). If they are not, regulate the distance
SUPERTYPE RS BRAKES
by turning the regulation screw on the cable tension (E) (Pic. 2).
If that is not sufficient, loosen the cable clamp screw (D) (Pic. 2),
increase the cable tension and tighten the cable clamp screw back
down (D) (Pic. 2) with a torque of 5 Nm.
Check that the cable is firmly fixed in place, without damaging it,
so that it does not work loose when the brakes are used, as if it is
loose or damaged it could mean the brakes would no longer work
and cause accidents and serious or mortal injuries.
• The Supertype RS brakes have pad holders with orbital regu-
lation, which means the brake pads can be regulated in height,
in parallel, horizontally and vertically with respect to the braking
surface. The pad holders are fixed in place by screwing down the 4
mm Allen screw (F) (Pic. 4) with a torque of 8 Nm.
On the brakes with pad holder, always check that the closed part
of the holder is facing the riding direction and that the pad fixing
screw (G) (Pic. 4) is correctly closed with a 2 mm Allen screw. If the
pad holder is not mounted correctly, the pad could slip and cause
accidents and serious or mortal injuries.
CHANGING THE BRAKE PADS
a) Always change both brake pads at the same time.
b) Remove the fixing screw from the brake pad (G) (Pic. 5) using a 2
mm Allen spanner, on both the right and left pad-holder.
c) Remove the brake pad by sliding it along the groove in the pad
holder (Pic. 5).
d) Fit the left brake pad in the left pad-holder and the right brake
pad in the right pad-holder as shown on the rear of the pad itself:
(R right – L left) (Pic. 6).
e) Tighten the pad fixing screw (G) (Pic. 6) with a 2 mm Allen
spanner.
if it works loose, the brake pad could fall out and cause accidents
or serious or mortal injuries.
f) Check the distance between the brake pads and rim is approx.
1.5-2 mm (Pic. 3).

MAINTAINING THE BRAKES

• Periodically check the brake pads for signs of wear, and replace
them when the braking surface is near to the end of the grooves or
when their braking power is not sufficient.
• Periodically check that brake pads are 1.5-2 mm from the sur-
face of the rim. If they are not, regulate the distance by turning the
regulation screw on the cable tension (E) (Pic. 2). If that is not suffi-
cient, loosen the cable clamp screw (D) (Pic. 2), increase the cable
tension and tighten the cable clamp screw back down (D) (Pic. 2).
Check that the cable is firmly fixed in place with an Allen spanner
with a torque of 5 Nm, without damaging it, so that it does not
work loose when the brakes are used, as if it is loose or damaged it
could mean the brakes would no longer work and cause accidents
and serious or mortal injuries.
USEFUL TIPS TO ENSURE THE BRAKES
WORK CORRECTLY
• Periodically have the tightening torque on the brake fixing screws,
the pad fixing and the cable fixing checked by a specialised ope-
rator.
• If the brakes are used under the rain, sand or dirt could build
up on the brake pads, which could damage the rims even on one
single outing.
• To keep the pads efficient and prevent wear to the braking surfa-
ce on the rims, we advice checking them frequently and immedia-
tely removing any foreign bodies that deposit on the pads.
3
Check the fixing screw is firmly tightened down, because
ENGLISH

Publicité

loading