Flight Control - Revell Control FORMULA Q FPV Manuel De L'utilisateur

6 trim adJustmEnt oF thE control
The model must be switched on first in order to connect it to the remote control.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
helicopter approximately 0.5 to 1 metre in altitude.
6A If the model automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight (2E) in the opposite direction.
6B If the model moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation (2C) incrementally in the opposite direction.
6C If the model automatically moves slowly or quickly forwards or backwards ...
gradually press the forwards/backwards trim (2D) in the opposite direction.

7 Flight control

Note: Only minimal corrections of the controls are necessary for a smooth flying behavior
of the model! The direction indication applies when the model is viewed from behind. If
the model is flying forwards towards the pilot, it must be moved in the opposite direction.
7A Take off or increase altitude by carefully moving the control for thrust and
rotation (2A) forward.
7B Land or decrease altitude by moving the control for thrust and
rotation (2A) backward.
7C Fly forward by moving the controller for forward/backward and sideways
flight (2B) carefully forward.
7D Fly backward by moving the controller for forward/backward and sideways
flight (2B) carefully backward.
7E Fly to the left by moving the controller for forward/backward and sideways
flight (2B) carefully to the left.
7F Fly to the right by moving the controller for forward/backward and sideways
flight (2B) carefully to the right.
7G Turn the model around to the left by moving the control for thrust and rotation (2A)
to the left.
7H Turn model around to the right by moving the control for thrust and rotation (2A)
to the right.
Button for shooting photos (2G): A photo is shot and saved to the memory card in
the camera in the model by pressing button 2G. Please ensure that the plug of the
camera is completely inserted in the camera connection (1G).
Button for video recording (2H): A video recording to the memory card in the
camera in the model is started by pressing button 2H. Pressing it again stops the
recording.
Flying faster: You can switch between the second and third speed levels by pressing
vertically on the controller for thrust and rotation (2A). Pressing the button again
switches back to the first speed level.
Flip function: The flip function is activated by pressing vertically on the controller for
forward/backwards and banking (2B). The next input with the controller (2B) deter-
mines the direction of the flip. Only activate this mode when there is adequate space
and the model is flying at a height of at least 2 metres.
18
Coming Home: Pressing the Coming Home button 2J commands the model to fly
back in the approximate direction of the take-off position. Please note that the model
calculates the direction of the take-off position and maintains this direction until it is
controlled by the pilot again. It is also possible that the model is not steered in the
direction of the take-off position due to the influence of wind or collisions.
Button for Headless Mode (2K): Headless mode supports beginners in the initial
stages. Regardless of where the quadrocopter turns, the direction of flight always
corresponds exactly to the direction specified with the control for forwards/backwards
and sideways movement (2B). An example: If the model were to be turned 180°
and flown towards the operator, the operator would have to „convert" the forwards/
backwards and sideways movement accordingly. This is no longer necessary if head-
less mode is activated, as the internal processor always converts the control directions
automatically. Pressing the 2K button again deactivates the mode
Attention: The model „notes" the forwards direction during each switch-on. This
means that the operator must not turn when controlling the model, as this would
change the concept of „forwards" and „right/left" in relation to the model. If the operator
changes position and wants to use headless mode - or if the control direction is no longer
correct due to a collision, the model must be restarted.
Display setup: The remote control also has a micro SD card slot (2P) on the right-
hand side. If a memory card is used here, a video can be recorded by pressing button
2I and a photo can be shot by pressing button 2L. However, the video and photo qual-
ity is lower when recorded in the remote control.
A longer press of button 2I opens the Setup menu. The VIEW and BRIGHTNESS
options can be selected with button 2I; button 2L opens the respective menu. Recor-
ded videos and photos can be viewed in the VIEW menu. The brightness of the display
can be adjusted in the BRIGHTNESS menu. The menu is closed by pressing button 2I.
BATTERy STATuS:
• The battery is empty if the model begins to lose thrust. Land in order to avoid crashing.
8 loading thE mEmorY card
A USB adapter is included for loading the photo and video files recorded on the micro
SD card. Insert the micro SD card in the USB adapter and connect the adapter to a USB
port of a PC or MAC. The files can be downloaded after a brief installation process.
Please following the procedure of your operating system for this purpose.
instructions For saFE FlYing
GENERAL FLyING TIPS:
• Always place the model on a level surface. An inclined surface can, under certain
circumstances, have a negative impact on the starting behavior of the model.
• Always operate the controls slowly and with a gentle touch.
• Always maintain visual contact with the model and do not look at the remote control!
• Move the thrust control down again somewhat as soon as the model lifts off from
the ground. Maintain flying altitude by adjusting the thrust controller.
• If the model lowers, move the thrust control slightly upward again.
• If the model climbs, move the thrust control down slightly.
19