Allen-Bradley PowerFlex 40 Guide De Mise En Route page 133

Zie de gebruikershandleiding van de PowerFlex 40 voor meer informatie over parameters.
Nr. Parameter
A117 [Busreg.modus]
A118 [Stroomgrens 2]
A119 [Skip Frequency]
A120 [Skip Freq Band]
A121 [Stall Fault Time]
A122 [Verlies anal ing]
A123 [10 V bipol vrijg]
A124 [Var PWM uit]
A125 [Koppel prestatie mode] 0/1
A126 [Motorstroom]
A127 [Autotune]
A128 [Spanningsval IR]
A129 [Fluxstroomref]
A130 [PID trim hoog]
A131 [PID trim laag]
A132 [Sel PID ref]
A133 [Sel PID feedback]
A134 [PID prop verst]
A135 [PID integ tijd]
A136 [PID diff snelh]
A137 [PID setpunt]
A138 [PID dode zone]
A139 [PID voorbel]
A140- [Stp Logic 0 – 7]
A147
A150- [Stp Logic Time 0 – 7] 0,0/999,9 Secs
A157
A160 [Vrtr EM rem uit]
A161 [Vrtr EM rem aan]
A162 [Sel MOP reset]
A163 [DB drempel]
A164 [Comm.schrijfmodus]
A165 [Vrtrag anl verls]
A166 [Anal ing filter]
A167 [PID Invert Fout]
Min/Max Display/Opties
0/1 0 = "Uit"
0,1/(A van drive × 1,8) 0,1 A
0/400 Hz 1 Hz
0,0/30,0 Hz 0,1 Hz
0/5 0 = "60 sec"
1 = "120 sec"
2 = "240 sec"
0/6 0 = "Uit"
1 = "Fout (F29)"
2 = "Stoppen"
3 = "Ref nul"
0/1 0 = "Unipolair in"
0/1 0 = "Vrijgegeven"
0 = "V/Hz"
0,1/(A van drive × 2)
0,1 A
0/2 0 = "Gereed/Idle"
1 = "Stat tunen"
0,0/230,0 VAC 0,1 VAC
0,00/[Motorstroom] 0,01 A
0.0/400.0 0.1
0.0/400.0 0.1
0/8 0 = "PID uit"
1 = "PID setpunt"
2 = "0 – 10 V ing"
3 = "4 – 20 mA ing"
4 = "Comm.poort"
0/2 0 = "0 – 10 V ing"
1 = "4 – 20 mA ing"
0.00/99.99 0.01
0,0/999,9 Secs 0,1 sec
0,00/99,99 (1/sec) 0,01 (1/sec)
0,0/100,0% 0,1%
0,0/10,0% 0,1%
0,0/400,0 Hz 0,1 Hz
0001/bAFF 4 cijfers
Raadpleeg de Gebruikershandleiding van de
PowerFlex 40 voor een lijst met cijferopties.
0,1 sec
0,01/10,00 Secs 0,01 sec
0,01/10,00 Secs 0,01 sec
0/1 0 = "MOP ref nul"
0,0/110,0% 0,0%
0/1 0 = "Opslaan"
0,0/20,0 Secs 0,1 sec
0/14 1
0/1 0 = "Niet inverted"
Nederlands-19
Default
1 = "Vrijgegeven" 1
A × 1,5
0 Hz
0,0 Hz
3 = "360 sec" 0
4 = "480 sec"
5 = "Fout uit"
4 = "Ref min freq" 0
5 = "Ref max freq"
6 = "Ref int freq"
1 = "Bipolair in" 0
1 = "Uit" 0
1 = "Sensrlz vect" 1
Nominale A
2 = "Dynamisch tunen" 0
Nominale V
Nominale A
60.0
0.0
5 = "Setpnt, trim" 0
6 = "0 – 10 V, trim"
7 = "4 – 20 mA, trim"
8 = "Comm, trim"
2 = "Comm.poort" 0
0.01
0,1 sec
0,01 (1/sec)
0,0%
0,0%
0,0 Hz
00F1
30,0 sec
2,00 sec
2,00 sec
1 = "Save MOP ref" 1
100,0%
1 = "Alleen RAM" 0
0,0 sec
0
1 = "Inverted" 0