Components - Nice Mhouse SL1S Instructions D'installation Et D'utilisation

TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS
The product SL1S-SL10S is produced by Nice S.p.a. (TV) I. In order to improve its products, NICE S.p.a. reserves the right to modify the technical
characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes.
Note: all technical specifications refer to a temperature of 20°C.
Model/type
Product type
Adopted technology
Maximum start-up torque
Nominal torque
No-load speed
Speed at nominal torque
Maximum frequency of cycles
Maximum time continuous cycle
Application limits
Mains power supply SL1SC-SL10SC
Mains power supply SL1SC-SL10SC/V1
Max. absorbed power
Backup power supply
Flashing light output
ECSbus output
"OPEN" input
"STOP" input
Radio aerial input
Max. cable length
Ambient operating temperature
Use in particularly acid, saline or
potentially explosive atmosphere
Assembly
Protection rating
Dimensions / weight
Possibility of remote control
Compatible GTX4 transmitters
GTX4 transmitter range
Programmable functions
Self-programmed functions
SL1SC
Electromechanical gearmotor for the automation of automatic gates and doors with built-in control unit
complete with radio receiver for "GTX4" transmitters.
24 motor, helical gear reducer; mechanical release. A transformer incorporated inside the motor but
separated from the control unit, reduces the mains voltage to the nominal 24 V
whole automation system.
10 Nm
3,5 Nm
0,25 m/s
0,20 m/s
14 cycles/hour at 25 °C
10 minutes
The structural design of this product makes it
suitable for use on gates with a weight up to 400
kg or leaf width up to 5 m.
230 V (+10% -15%) 50/60Hz
120 V (+10% -15%) 50/60Hz
370 W
For "PR1" buffer batteries
For flashing lights with 12 V (maximum 21 W) bulb
1 output with maximum load of 10 ECSBus units
For normally open contacts (closure of the contact prompts the "OPEN" command)
For normally open and/or 8,2KΩ constant resistance type contacts, or normally closed contacts with
self-learning of the "normal" status (a variation with respect to the memorised status generates a
"STOP" command)
52Ω for RG58 or similar type cable
Mains power-supply: 30 m; inputs/outputs: 20 m with antenna cable preferably less than 5 m
(observe warnings regarding the minimum section and type of cables
-20 ÷ 50°C
NO
Horizontal on a flat surface with the specific fixing plate
IP44
300 x 163 h 295 mm / 7,5 kg
With "GTX4" transmitters, the control unit is set to receive one or more of the following commands:
"OPEN", "Partial Open", "Only Open" and "Only Close"
Up to 150 if memorised in mode 1
50-100 m. This distance may vary in the presence of obstacles and electromagnetic disturbance present,
and is influenced by the position of the receiving antenna built into the flashing light.
"Single cycle" or "Complete cycle" (automatic closure) operating mode
Motor speed "slow" or "fast"
Pause time in "complete cycle" selectable from 10, 20, 40, and 80 seconds
Type of partial opening selectable from 4 modes
Obstacle detection system sensitivity selectable on 4 levels
"Open command" operating mode selectable on 4 modes
Self-learning of devices connected to the ECSBus output
Self-learning of type of "STOP" device (NO, NC or 8,2 KΩ resistance contact)
Learning of gate length and calculation of the points of deceleration
SL10SC
voltage used in the
15 Nm
5,2 Nm
0,18 m/s
0,15 m/s
12 cycles/hour at 25 °C
7 minutes
The structural design of this product makes it
suitable for use on gates with a weight up to 550
kg or leaf width up to 7 m.
420 W
300 x 163 h 295 mm / 8,5 kg
25