Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Tape measure
#2 Phillips screwdriver
¹⁄₈" x 4¼" flat-blade
screwdriver
Level
Drill
Wrench or pliers
Pipe wrench
Adjustable wrench or
⁵⁄₈" wrench
³⁄₈" drive ratchet
¹⁄₈" drill bit
¹⁵⁄₁₆" combination wrench
¹⁄₄", ³⁄₈", ⁵⁄₁₆" nut drivers
Parts supplied
Check that all parts are included.
Anti-tip bracket kit
A
A. Anti-tip bracket
B. #8-18 x 1" Phillips head screws (4)
NOTE: Anti-tip bracket must be securely mounted to
subfloor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store. See "Install Anti-Tip Bracket"
section.
Gas pressure regulator
Burner grates
†®TORX is a registered trademark of Acument Intellectual Properties, LLC.
4
A child or adult can tip the range and be killed.
Connect anti-tip bracket to wall behind range.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.
INSTALLATION REQUIREMENTS
³⁄₁₆" carbide tip masonry bit
Marker or pencil
Pipe-joint compound
resistant to LP gas
Noncorrosive leak-detection
solution
Tubing cutter
For LP/Natural Gas
Conversions
®†
T15 Torx
screwdriver
⁷⁄₈" socket
Adjustable wrench
½" deep-well socket
7 mm nut driver
Masking tape
B
WARNING
Tip Over Hazard
Tools and Parts
Burner heads and caps
Grill grate (on grill models)
Wave tray (on grill models)
Flame spreader (on grill models)
Burner assembly (on grill models)
Grease trays (2) (on grill models)
Griddle drip tray (on griddle models)
Grill drip tray (on grill models)
Island trim
LP orifice package (W10221288)
Conversion label (W10221320)
NOTE: The cooktop is manufactured for use with Natural gas.
To convert to LP gas, see the "Gas Conversions" section.
Additional Parts Supplied on Steam-Assist Models
Model W10049700 water filter kit
¼" to ¼" water supply union
Parts needed
Power supply cord kit:
30" (76.2 cm) and 36" (91.4 cm) models - A UL listed
40 amp power supply cord kit
48" (121.9 cm) models - A UL listed 50 amp power supply
cord kit marked for use with nominal 1³⁄₈" (34.93 mm)
diameter connection openings
A UL listed strain relief
UL listed wire connectors
All models must be installed with a backguard if installing at
zero clearance to a combustible backwall. See "Cabinet
Dimensions" in the "Location Requirements" section for
installation requirements.
30" (76.2 cm) Adjustable Backguard
Order Part Number 8285148
36" (91.4 cm) Adjustable Backguard
Order Part Number 8284756
48" (121.9 cm) Adjustable Backguard
Order Part Number 8284755
9" (22.9 cm) Backguard for 30" (76.2 cm) Ranges
Order Part Number W10115773
9" (22.9 cm) Backguard for 36" (91.4 cm) Ranges
Order Part Number W10115776
9" (22.9 cm) Backguard for 48" (121.9 cm) Ranges
Order Part Number W10115777
Publicité
Table des Matières
