Customer Service - Peg-Perego Polaris RZR 900 XP Guide D'utilisation Et Entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
MAINTENANCE AND VEHICLE
CARE
• Do not disassemble or try to repair the vehicle on
your own. Contact an authorised Peg Perego
customer support centre.
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used.
• Always disconnect the battery charger from the
toy before carrying out cleaning, maintenance, or
any type of intervention.
• For repairs use only original PEG PEREGO spare
parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE SCREWS
AND SMALL PARTS ARE CONTAINED IN A BAG
INSIDE THE PACKAGING. THE BATTERY MAY
ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while assembling
the toy, given the risks caused by small parts (ingestion
hazard) and the plastic bags that contain them
(choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a pair
of pliers.
ASSEMBLY
1 • Remove the chassis from the packaging and
position it on its side. Snap fit the teeth of the 2
supports onto the chassis.
2 • Position the chassis horizontally and screw up the
4 internal screws while holding the 2 supports in
position.
3 • Push the 2 rear cylindrical shock absorbers into
the slots, ensuring that the sides are correct (right
and left are indicated on the back of the items).
4 • Press the side panel into the 2 slots on the
chassis, paying attention to the lights system cable.
Insert the other side panel on the opposite side.
5 • Insert the lights system cable into the roll bar
support. Position the roll bar support by engaging
the rear part first and then the front part. Do the
same with the other support.
6 • Fix on the supports with the screws provided.
7 • Connect the 2 roll bar light cables and insert the
roll bar into the vertical supports.
8 • Fix the roll bar using pressure to engage the 2
self-threading screws, one on each side.
9 • Apply the stickers in the 2 rear light seats.
10 • Push the rear lights into the respective seats.
11 • Position the seat as required (the seat can be
fitted in 2 positions) and fix it with the 2 screws
provided. Fit the other seat in the same way.
12 • Insert the 2 seatbelt buckles into the respective
central slots between the seats, as shown in the
figure.
13 • Fit the 2 ring clamps on the roll bar, one on each
side, opening them to position them correctly.
14 • Fix the 2 belts to the respective ring clamps with
the screws provided.
15 • Join the two sections of the steering wheel.
16 • Remove the plastic protection from the steering
column. Connect the steering wheel cable to the
dashboard cable. WARNING: place the cables in
their housing taking care they don't get crushed.
Fit the steering wheel on the steering column,
lining up the respective holes.
17 • On one side insert the screw and on one other
the nut, and fix the steering wheel as shown in the
figure.
18 • Install the two parts of the windshield as shown.
Picture A shows the grille fitted correctly
19 • Secure the grille with the three screws.
20 • Place the windshield on the hood hooking the
three central tabs.
21 • Fit the windscreen of the vehicle with screws.
22 • Snap fit the 2 remaining front shock absorbers,
ensuring that the sides are correct (right and left
are indicated on the back of the items).
23 • Connect the front lights as shown in the figure.
24 • Fit the front cover engaging it to the chassis at the
6 points highlighted in detail A.
25 • Screw on the cover with the 2 screws provided.
26 • Apply the silvered stickers in the 2 front light
seats.
27 • Push the front lights into the respective seats.
28 • Remove the protective caps from the steering
levers. On one side, slide on one of the large
washers provided.
29 • Fit one of the two front wheels (the narrower
ones) on this same side. Keep the wheel trim on
the outside (check that it is fitted onto the wheel
and attach it to its pin if necessary). Next, insert a
small washer and then the nut. Tighten the nut to
secure the wheel. Use the same procedure to fit
the other front wheel.
30 • Remove the protective caps from the rear axle
and insert the axle into the rear of the vehicle as
shown in the figure.
31 • On one of the rear wheels, on the opposite side
to the rim, push on a driver. Now slide the wheel
onto the axle, and keep it in position while fitting
the other rear wheel in the same way.
32 • Fit a small washer and nut on both wheels.
Tighten the nuts using the spanner provided on
one side and a pair of pliers on the other.
33 • Snap fit the 4 wheel hubcaps.
34 • Open the battery compartment by rotating the
red catch to the lock open position. Connect the
electrical system plug with the battery plug.
35 • Close the battery compartment by inserting the
cover at the front below the cover plate.
Complete the operation by inserting the red
catch and rotating it 180º using a coin. The vehicle
is now ready for use.
FEATURES AND INSTRUCTIONS FOR
USE
36 • A - passenger handrail
B - horn activating button
C - low battery indicator
• blinking LED: 20% battery level
• steady LED: 10% battery level
D - radio FM, MP3 input, USB port, MICRO SD
slot
E - START button
F - electric accelerator and brake pedal. Lift the
foot from the pedal to engage the brake
automatically.
WARNING: lights and sounds deactivate after 3
minutes if the vehicle remains inactive. Press
START or the accelerator to reactivate them.
37 • To release the seat belt: 1 pull towards the centre
while pushing the button; 2 disengage.
38 • Rear DRINKS HOLDER. There is a double drinks
holder in the rear box.
39 • ADJUSTABLE SEATS. The seats can be adjusted in
2 positions as the child grows, as shown in the
figure.
40 • GEAR LEVER: when supplied the vehicle speed is
limited to first gear (1 - see figure). It also has a
reverse (R), and a second gear (2) recommended
only for expert drivers. To enable the second gear,
unscrew the red stop on the gear lever.
41 • Rotate the stop 90°, as shown in the figure, and fix
in position with the screw. Now by pulling back
the gear lever the vehicle can run in second gear.
42 • ACCESSORY: trailer to attach to the vehicle (sold
separately).
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
43 • Use a coin to open the battery compartment.
Disconnect the battery from the system. Remove
the 2 screws from the battery holder in the
compartment.
44 • Replace the flat battery. Put the battery holder
back in place and secure it with the screws.
Connect the two plugs, close the battery
compartment and fasten it shut.
BATTERY CHARGING
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
45 • Disconnect plug A of the electrical system from
plug B of the battery by pressing laterally.
46 • Connect the battery charger to a domestic power
outlet according to the instructions included with
the charger. Connect plug B with plug C of the
battery charger.
47 • When charging is complete, disconnect the
battery charger from the power outlet and then
disconnect plug C from plug B.
48 • Fully insert plug B into plug A, until it snaps into
position. At the end of charging operations always
remember to insert and fix the battery holder.
Close the battery compartment and secure it
with the catch.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Igod0554

Table des Matières