Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Pag. 24 di 40
E
B - ADJUSTING THE MICROSWITCHES
N
DIP 1
CHECKING THE ROTATION DIRECTION OF THE MOTOR
G
(ON) (POINT C)
L
DIP 2
TIMING (ON) (POINT D)
OPERATING MICROSWITCH
I
DIP 3
Pausing time before automatic closing in normal and
S
pedestrian mode (ON)
DIP 4
Jogging radio receiver (OFF) - automatic (ON)
H
DIP 5
Single impulse command (K BUTT) jogging (OFF) - automatic (ON)
DIP 6
Photocells always active (OFF) - Photocells active only on closure (ON)
DIP 7
Encoder - OBLIGATORILY IN "OFF" MODE -
DIP 8
Pre-blinking (ON) - Normal blinking (OFF)
DIP 9
Deceleration (ON)
DIP 10 Electronic brake - OBLIGATORILY IN "ON" MODE -
DIP 11 Gradual start - OBLIGATORILY IN "OFF" MODE -
DIP 12 230V Motor (OFF) 120V (ON)
TORQUE - ELECTRONIC TORQUE REGULATOR
The torque is regulated by rotating the Trimmer TORQUE, varying the output voltage of
motor ends,(when rotated clockwise, more torque Is transmitted to the motor).
Such torque Is automatically Included 2 seconds after the start of every operating cycle.
This allows the motor to have the maximum pickup when it starts.
LOW SPEED – SPEED ADJUSTMENT DURING DECELERATION
When the DIP 9 is in ON position the speed during the deceleration is adjusted by turning
the trimmer indicated as LOW SPEED. This trimmer is used to change the speed of the
motor when the gate is approaching the last part of the run, both in opening and closing.
(to increase the speed, the trimmer must be turned clock wise).
The deceleration speed is set automatically by the control panel during the time
programming. The deceleration starts automatically about 15-20 cm before the gate
reaches the limit switch in opening and closing.
ELECTRONIC BRAKE (obligatory operation)
With DIP 10 in ON mode, the system shall brake once the total opening or closing have
been carried out, so to avoid the inertia that would damage the gear in the event of an
impact against the mechanical stops.
The electronic brake works also during the movement, when an obstacle is moved
between the photocells.
GRADUAL START (suggested operation)
If DIP 11 is ON, a gradual movement is enabled at every operation start.
This function is not active in case of a safety device detects an obstacle.
DL1 photocells contact (NC)
DL2 stop contact (NC)
DL3 opening limit switch contact (NC)
DL4 closing limit switch contact (NC)
DL5 programming operated
DL6 gate on opening "OPEN" (green)
DL7 gate on closure "CLOSE" (red)
DL8 manual release safety device (NC)
DL9 - NOT QUALIFIED -
C - CHECKING THE ROTATION DIRECTION OF THE MOTOR
This control is carried out to facilitate the installation of the system or any possible future
control.
1 - After you have ensured the correct positioning of the limit switch plates (fig. 7),
manually move the gate to half open position;
2 - Put DIP 1 in the ON mode => The LED DL5 starts blinking;
3 - Press the PROG button and hold it (the gate now is controlled in a dead man mode:
open, stop close stop open) => THE RED LED DL7 "CLOSE" turns on and the gate
starts closing (if it does not close, invert the wires of the motor V and W) until it
reaches the limit switch of the close position (if the gate and motor do not stop, release
the PROG button and invert the position of the J9 connector);
4 - Press the PROG button and hold it => THE GREEN LED DL6 "OPEN" turns on and
the gate opens until it reaches the limit switch for opening position;
5 - After 2 sec. and within 10 sec. of continuous work, both in closing or opening,
the electronic clutch intervenes automatically. Adjust the force of the clutch by
turning the appropriate trimmer "TORQUE".
6 - After 10 sec. of continuous work, both in opening and closing, the automatic
deceleration is activated (if DIP 9 is on ON position) Adjust the speed of the
operator requested during the deceleration by turning the appropriate trimmer
"LOW SPEED".
7 - At the end of the control, and of the trimmers' adjustements, position DIP1 on
mode OFF. The LED DL5 turns off, signalling you exit from the control.
NB: The photocells are not active during this control.
LED SIGNALS
D - TIMING
N.B.: DIP7 HAS TO BE IN "OFF" MODE.
The programming can be carried out regardless of the gate position.
1 - Put DIP 2 in the ON mode => the LED DL5 emits short blinkings.
2 - Push the button PROG. => the gate closes and opens automatically 2 seconds after it
closed. When the opening cycle Is terminated, It stops. Wait as long as you want the
gate to remain open (excluded by DIP3 OFF).
3 - Push the button PROG. to command the gate closing (also the pause time count
before the automatic closing stops - max. 5 minutes).
4 - The gate stops as the closing cam is reached.
5 - WHEN THE TIME PROGRAMMING IS COMPLETED, POSITION DIP 2 ON MODE
OFF.
NOTE: The deceleration speed is set automatically by the control panel during the time
programming. The deceleration starts automatically about 15-20 cm before the
gate reaches the limit switch in opening and closing.
OPERATION OF THE OPERATING ACCESSORIES
OPENING BUTTON (with timer function)
When the gate is standstill, the button operates the opening mode. If you push this button
when the gate is on closure, it opens again.
TIMER FUNCTION
This function is useful In the rush hours, when vehicle traffic is slow (e.g. entry/exit of
workers, emergencies In residential or parking areas and, temporary, for removals).
APPLICATIONS
By connecting a switch and/or a daily/weekly timer (in place or in parallel with the opening
button N.O. "COM-OPEN"), it is possible to open the automation or to keep It open, as
long as the switch is on or the timer is activated.
When the automation is open, all operating functions are inhibited.
If the automatic closing Is started, by releasing the switch or at the time set before, the
automation immediately closes; if not, you need to operate a command.
CLOSING BUTTON (COM-CLOSE)
When the gate is standstill, it operates the closing.
JOGGING OPERATION BUTTON (COM-K BUTTON)
If DIP5 is OFF => It cyclically commands open-stop-close-stop-open-etc.
If DIP5 is ON => It opens the gate when this Is closed. If it is operated while the gate Is
opening, It has no effect. If it is operated when the gate is open, it closes
the gate and, if it is operated while the gate is closing, it opens the gate
again.
RADIO TRANSMITTER
If DIP4 is OFF => It cyclically commands open-stop-close-stop-open-etc.
If DIP4 is ON => It opens the gate when this is closed. If it is operated while the gate Is
opening, It has no effect. If it is operated when the gate is open, it closes.
If it is operated while the gate is closing, it opens the gate again.
AUTOMATIC CLOSING FOR COMPLETE OR PEDESTRIAN OPENING
The pausing time before the automatic closing for both, complete or pedestrian opening is
set during the time programming. In both cases the maximum pausing time available is 5
minutes. Pause time can be started or stopped by DIP3 (ON started).
OPERATION AFTER BLACK-OUT
When mains electrical power is restored press the opening button (K, OPEN, radio).
Let the gate close itself with automatic closure or to command the
The gate will open.
closing movement. This operation is valid to obtain the leaves position readjustment.
During this phase all safety devices are active.
Publicité
Table des Matières
