UFESA AP9000 Mode D'emploi page 17

4
Open the filler cap and fill the cleaning fluid
reservoir (23) with cleaning agent (a mixture of cleaning
fluid G 500 O Tens (29) and cold water). Use the
amounts stated on the fluid bottle label:
– "G 500 O Tens" manufactured by BUZIL, Germany.
● Close the filler hole of cleaning fluid reservoir with
the cap.
Before wet cleaning the carpet, check the
colour fasteness of cleaned carpet. Put
a small amount of prepared solution on
white cloth and clean manually the carpet at
least visible place. If the cloth is dyed, it means
that the carpet colours are not permanent and
the carpet cannot be cleaned using cleaning
fluid G 500 O Tens.
5
Insert the cleaning liquid container (23) back to
the previous position and press the container to fix it
correctly (proceed in the reverse order as in case of
removing the container).
6
Insert the container together with the water filter
module (filter unit and partition) to the vacuum cleaner.
For protection against the formation of foam or at
its formation, when cleaning fill the rear tank with an
anti-foaming agent (29) in the amounts specified on
the label:
– "G 478 Buz® Defoam" manufactured by company
BUZIL, Germany.
● Prepare the vacuum cleaner for operation according
B
to section .
Use only the large or small atomizing
nozzle for wet vacuum cleaning.
● The vacuum cleaner starts at the same power level
it had been working before it was turned off. Set the
desired power value by pressing the power adjustment
buttons +/- (9).
7
Press the pump switch (7).
The pump may only be switched on
when the cleaning liquid container is
filled with the solution of cleaning liquid
and water. The lack of cleaning liquid manifests
in a loud operation of the pump.
If the nozzle does not atomize water although the
pump is switched on, check if the following items
are correctly installed: the cleaning liquid container
(press the container), the fastening of the stub pipe
in the valve in the base of the vacuum cleaner or the
fastening of the hose end in the atomizing nozzle,
check if the atomizing nozzle is not clogged.
8
Press the button adjusting the inflow of water to
the nozzle on the hose handle.
If you press the button in a pulsating manner, the water
shall temporarily flow in a slower manner to the nozzle,
if you press and slide the button backwards, the water
shall be continuously supplied to the nozzle.
The handle is also equipped with a slider to adjust
the suction power. Do not uncover this opening while
picking up water or using the wet cleaning function.
Do not spray the cleaning liquid in one
place on the carpet for too long in order
not to soak the carpet.
● You should to clean the carpet in such a way that
during and immediately after cleaning nobody walks
on the cleaned surface. After cleaning one part of the
carpet stop the spraying process and dry the carpet
by sliding the nozzle back and forth. Repeat until the
whole surface of the carpet is dried.
● After ending the spraying process switch off the
pump and press the button adjusting the water inflow
to the nozzle for a moment to "release the pressure".
The vacuum cleaner is equipped with
a float which will automatically block the
suction if the foam filter II (31) is heavily
dirty or the liquid exceeds the maximum level.
It is manifested by a pulsing limitation of the
motor power and the lighting up of the clogged
air inlet indicator (12). In such a case switch off
the vacuum cleaner by pressing the on/off
button (8), unplug the appliance, clean the filter
and empty the container.
Make sure the carpet is not soaked.
It may lead to a permanent deformation
of the carpet (folding).
PICKING UP WATER
If you want to use the vacuum cleaner to vacuum
liquid in the container, the vacuum cleaner should be
prepared as in the case of vacuum cleaning with the
use of the water filter module except that:
1. The container should be empty (without water).
2. You are to use atomizing nozzles (large or small),
large atomizing nozzle with the gathering attachment
or the nozzle for picking up water.